Soundstream D-Tower DTR1.1700

Questions and Answers

E
Elizabeth CooperJul 29, 2025
What to do if the Protection LED comes on in my Soundstream Car Amplifier?
- D
  Darryl WadeJul 29, 2025
  If the Protection LED on your Soundstream Car Amplifier is illuminated, it indicates a potential issue. First, examine the speaker leads for any short circuits; if found, remove the speaker lead and reset the amplifier. Also, ensure the speaker load isn't below the minimum specified limit. If the LED remains on after these checks, the amplifier may be faulty and require professional servicing.
C
Charles BensonAug 2, 2025
How to fix distorted sound in a Soundstream D-Tower DTR1.1700 Car Amplifier?
- D
  diana85Aug 2, 2025
  If your Soundstream Car Amplifier is producing distorted sound, start by checking the input level control to ensure it matches the signal level of your head unit. It's best to keep the input level as low as possible. Also, verify that all crossover frequencies are correctly set. Finally, check the speaker leads for short circuits.
P
Pamela FernandezAug 6, 2025
Why won't my Soundstream D-Tower DTR1.1700 power up?
- L
  Levi GordonAug 7, 2025
  If your Soundstream Car Amplifier isn't powering up, there are several things to check. First, ensure you have a solid ground connection. Next, verify that battery power is reaching the (+) terminal. Inspect all fuses and replace any that are blown. Finally, check that the Protection LED is not lit.
I
ithompsonAug 10, 2025
What causes my Soundstream Car Amplifier to get very hot?
- M
  Monica ManningAug 11, 2025
  If your Soundstream Car Amplifier is getting excessively hot, make sure the minimum load impedance for your specific amplifier model is correct. Also, ensure there's adequate air circulation around the amplifier. In some cases, adding an external cooling fan may be necessary.
M
Mrs. Gail MartinezAug 15, 2025
How to increase low output on a Soundstream D-Tower DTR1.1700 Car Amplifier?
- B
  Bryce CollierAug 15, 2025
  To address low output from your Soundstream Car Amplifier, begin by resetting the level control. Also, check the crossover control settings to ensure they are properly configured.
Y
ysingletonAug 19, 2025
How do I stop high hiss in the speakers of my Soundstream D-Tower DTR1.1700?
- T
  timothybellAug 19, 2025
  To eliminate high hiss from the speakers connected to your Soundstream Car Amplifier, check that the RCA cable isn't shorted to the power ground on the amplifier's side. Also, inspect the amplifier's grounding connection.
B
bwintersAug 23, 2025
What to do if my Soundstream Car Amplifier has no output?
- M
  Michael FryeAug 23, 2025
  If there's no output from your Soundstream Car Amplifier, first check that the RCA audio cables are correctly plugged into the appropriate inputs. Next, inspect all speaker wiring. Finally, check the head unit output and the amplifier level setting.

Summary

Control Functions Explained

Speaker and Power Terminals

Connect speakers/subwoofers and the +12 Volt power supply with a fuse.

Remote Turn-On and Ground Connections

Connect the remote turn-on lead and the ground cable to the vehicle frame.

Input Signal Options

Utilize RCA input jacks or high-level inputs for audio signal.

Remote and Level Controls

Crossover and Filter Adjustments

Bass Boost and Phase Settings

Installation and Mounting

Installation Precautions

Carefully investigate car layout and disconnect battery before installation.

Amplifier Mounting Methods

Connecting the Amplifier

Cable and Fuse Specifications

Ground, Power, and Remote Wiring

Input and Final Connections

Wiring Diagrams

Troubleshooting Common Issues

Amplifier Power and Protection Issues

Diagnose problems like no power or protection LED activation.

Audio Output Problems

Resolve issues such as no output, low output, or distorted sound.

Noise and Overheating

Troubleshoot high hiss in speakers and amplifier overheating.

Technical Specifications

Soundstream D-Tower DTR1.1700 Specifications

General

Channels	1
Power Output	1700W
RMS Power @ 2 Ohms	850W x 1
RMS Power @ 1 Ohm	1700W x 1
Frequency Response	20Hz - 220Hz
Signal to Noise Ratio	>90dB
Damping Factor	>150
Input Sensitivity	200mV - 6V
Crossover Type	Variable Low Pass
Subsonic Filter	10Hz - 50Hz
Bass Boost	0 to +12 dB
Bass Boost Frequency	45Hz
Dimensions	10.25"W x 2.25"H x 17.75"L
Phase Shift	0 - 180 degrees
Operating Voltage	9V - 16V
RMS Power at 2 Ohms	850W x 1
RMS Power at 1 Ohm	1700W x 1