Soyal AR-331-E - Page 12

V220922
- 11 -
Fingerprint
Biometrics Device Access controller
28 ???
※
Default Value
Function Option Value
Bit
Application
Expiry User Access Trigger Alarm
※
0: Disable 1: Enable 001 0 Networking/Stand-Alone
Reset Anti-Passback on Timezone 61
※
0: Disable 1: Enable 002 1 Networking/Stand-Alone
--- ---- ---- 004 2 ----
Duress and Arming Output function 0: Wiegand Output 1: Arming and Duress Output 008 3 Networking/Stand-Alone
RS-485
Lift Control: 0 000
4-5 Networking/Stand-Alone
Host: 1 016
LED Board: 1 032
Printer: 1 048
---- ---- ---- 032 6 ----
---- ---- ---- 064 7 ----
34 ???
44 ???
Function
Function
Option
Option
Value
Value
Bit
Bit
Application
Application
※
Default Value
※
Default Value
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
※
0
：
Disable
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
Networking/Stand-Alone
001
002
004
008
016
001
002
004
008
016
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
1
：
Enable
0
1
2
3
4
0
1
2
3
4
Turn o󰀨 buzzer function
Any error trigger alarm (ex: swipe invalid card)
Reserved
Turn o󰀨 13.56MHz reading function
Turn o󰀨 125kHz reading function
Access valid door relay remain locked
Master/Slave interlocking (Master open, Slave
could not open door)
Reserved
Stop card access (access only by PIN or PC
remote open door)
Reserved
※
More Details
：
Introduction of New Function Commands for Enterprise E Controller and Home H Controller
◎
Add value 032 means to activate, deduct value of 032 means to disactivate the function of swipe any tags to release door open
24 0 ??? (Main Controller Parameter Setting)
24 1 ??? (WG Input Port Parameter Setting)
※
Default Value
Function Option Value
Bit
Application
Enable Egress Beep Sounds 0: Disable
※
1: Enable 001 0 Networking/Stand-Alone
---- ---- ---- 002 1 ----
---- ---- ---- 004 2 ----
Arm/Disarm Zone(Zone: 62)
※
0: Enable 1: Disable 008 3 Networking/Stand-Alone
Reader and controller share the same door relay
(only for WG reader)
0: Disable
※
1: Enable 016 4 Networking/Stand-Alone
◎
Enable swipe any tags to release door open
※
0: Disable 1: Enable 032 5 Networking/Stand-Alone
Stop alarm by pressing push button or closing the door
※
0: Disable (must swipe valid card) 1: Enable 064 6 Networking/Stand-Alone
Enter auto open time zone without presenting valid card
※
0: Disable (must present valid card rst) 1: Enable 128 7 Networking/Stand-Alone