SL SERIES MANUAL 26 118006-001 REV Y
R E V . A
A S S Y 4 0 4 2 3 0 -
J B 1
J2
R 2 6
J1
J4
CR4
E1
J3
J B 2
T B 1
O U TP UT C URRE NT :
SP ECI AL FE AT URE S:
SPELLM AN
H I G H V O L T A G E E L E C T R O N I C S C O R P
P L A I N V I E W , N Y 1 1 8 0 3 M A D E I N U S A
PA RT NO . :
M O DE L :
PO L ARI T Y:
O U TP UT V O LT AG E :
DANGER
HI G H VO LTAG E
O U TP UT P O W ER :
1
115V
T1
E 3 6
E2
E 3 7
J B 2
JB2
J B 3
1
4
220V
115V
E 3 9
E 3 8
J B 9
J B 8
J B 7
J B 5
G2E 2 DE1G1 G1E1 E 2 DG2
E 3 0E 2 8
E 2 7E 2 0
E 1 3
E9 E 1 1
E 1 4
C1
E2
C 2 E 1
Q3
C1
E2
C 2 E 1
J3 J2
J4
J P 1 2
J P 1 3
J1
L1
Q2
L2
REMOVE COVER BY UNSCREWING AND REMOVING 12 SCREWS
THAT MOUNT COVER TO CHASSIS AND FRONT PANEL.
REMOVE 4 SETS OF HARDWARE THAT HOLD THE LEXAN COVER
TO THE HIGH VOLTAGE BOARD, AND REMOVE COVER.
TURN UNIT OFF, UNPLUG LINE CORD FROM AC OUTLET AND
WAIT FOR 5 MINUTES BEFORE PROCEEDING TO CHANGE THE
HIGH VOLTAGE MULTIPLIER.
1
2
REINSTALL LEXAN COVER AND RELATED HARDWARE.
REINSTALL POWER SUPPLY'S COVER AND ALL HARDWARE BEFORE
4
3
FOR POSITIVE POLARITY:
BLACK WIRE ON J4 AND WHITE WIRE ON J5.
FOR NEGATIVE POLARITY:
WHITE WIRE ON J4 AND BLACK WIRE ON J5.
SWAP BLACK AND WHITE WIRES BETWEEN J4 AND J5 AS FOLLOWS:
TURNING UNIT ON.
2
3
2
LI NE LO AD
600 to 1200 Watt
1kV to 8kV chassis
R E V . AA S S Y 4 0 4 1 2 9 - 0 0 1
1
5
1
4
S / S R E V . A
E4
J4
E2
JB 1
J B 2
J B 3
C1
E2
C2 E 1
G2E 2 DE1G1 G1E1 E 2 DG2
C1
E2
C2 E 1
1
1
AS S Y 4 0 3 9 3 5 -
RE V . A
S L 6 0 0 W - 1 2 0 0 W
CO N T R O L / P O W E R BD
115V
220V
115V
J B 1
J3 J2
J4
T1
J P 1 2
J P 1 3
J1
E 3 9
E 3 6
E2
E 3 7
J B 5
J B 2
E 3 8
Q3
J B 7
J B 6
E3
T B1
E 3 0E2 8
E 2 7E 2 0
E 1 3
E9 E1 1
E 1 4
L1
Q2
JB2
L2
J B 3
1
4
HIGH VOLTAGE
MULTIPLIER
8
UNIT ON.
INSTALL COVER AND ALL HARDWARE BACK BEFORE TURNING
5
7
6
4
3
2
1
HIGH VOLTAGE MULTIPLIER.
W AIT FOR 5 MINUTES BEFORE PROCEEDING TO CHANGE THE
TURN UNIT OFF, UNPLUG LINE CORD FROM AC OUTLET AND
REVERSE.
INSTALL NEW MULTIPLIER BY FOLLOWING STEPS 6 THRU 2 IN
CAREFULLY TILT UP AND SLIDE OUT MULTIPLIER.
ENCLOSURE AND THE BOARD TO THE CHASSIS
REMOVE 2 SCREW S THAT HOLD THE POLYETHYLENE
THAT MOUNT COVER TO CHASSIS AND FRONT PANEL.
REMOVE COVER BY UNSCREW ING AND REMOVING 12 SCREW S
FROM FASTON TAB ON BOARD.
UNPLUG CABLE FROM JB1 AND REMOVE CABLE SHIELD
UNPLUG CONNECTOR FROM JB2.
UNPLUG HIGH VOLTAGE LEADS FROM ASSEMBLY.
7
3
5
6
4
9
LI NE LO AD
600 to 1200 Watts
10kV to 120kV chassis
Figure 5.5 -- Polarity Reversal Procedures
600W to 1200W, 1kV to 8kV Chassis
Figure 5.6 -- Polarity Reversal Procedure
600W to1200W, 10kV to 120kV Chassis
To Next Page
