Stihl FS 410 C-M K User Manual

19.3 Sound Values and Vibration
Values
The K-value for the sound pressure level is
2 dB(A). The K-value for the sound power level is
2 dB(A). The K-value for vibration level is 2 m/s².
Using with a metal cutting attachment
FS 410 C-M K
–
Sound pressure level L
peq
measured accord‐
ing to ISO 22868: 99 dB(A).
–
Sound power level L
w
measured according to
ISO 22868: 109 dB(A)
–
Vibration level a
hv
measured according to
ISO 22867:
–
Control handle: 2.6 m/s².
–
Left handle: 2.5 m/s².
FS 460 C-M K
–
Sound pressure level L
p
measured according
to ISO 22868:
–
FS 460 C-M K: 100 dB(A)
–
FS 460 C-M K with handle heating:
101 dB(A)
–
Sound power level L
w
measured according to
ISO 22868:
–
FS 460 C-M K: 110 dB(A)
–
FS 460 C-M K with handle heating:
111 dB(A)
–
Vibration level a
hv
measured according to
ISO 22867:
–
Control handle: 2.4 m/s².
–
Left handle: 2.5 m/s².
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
19.4 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
19.5 Exhaust Emissions
The CO
2
value measured in the EU type approval
procedure is specified at www.stihl.com/co2.
The measured CO
2
value was determined on a
representative engine in accordance with a
standardized test procedure under laboratory
conditions and does not represent either an
explicit or implied guarantee of the performance
of a specific engine.
The applicable exhaust emission requirements
are fulfilled by the intended usage and mainte‐
nance described in this instruction manual. The
type approval expires if the engine is modified in
any way.
20 Combinations of Cutting Attachments, Deflectors and Carrying
Systems
20.1 Combinations of Cutting Attachments, Deflectors and Carrying Systems
Cutting attachment Deflector Carrying system
–
Brush knife 300-3 (300 mm
dia.)
–
Brush knife 305-2 "Special"
(305 mm dia)
–
Deflector for metal cutting attachments
–
Full harness with
quick-release sys‐
tem
–
200-22 circular saw blade,
chisel tooth (200 mm dia.)
–
Circular saw blade 200-22
chisel tooth HP (Ø 200 mm)
–
Circular saw blade 200-44,
scratcher tooth (200 mm dia.)
–
Limit stop with 200 mm diameter
–
Circular saw blade 225-48
scratcher tooth (225 mm dia.)
–
Circular saw blade 225-22
chisel tooth HP (Ø 225 mm)
–
225-24 circular saw blade,
chisel tooth (225 mm dia.)
–
225-36 circular saw blade, car‐
bide (225 mm dia.)
–
Limit stop with diameter 225 mm
English 20 Combinations of Cutting Attachments, Deflectors and Carrying Syst…
20 0458-839-0101-A

Stihl FS 410 C-M K Specifications

General

Brand	Stihl
Model	FS 410 C-M K
Category	Saw
Language	English