Why Stihl Cordless Saw has poor cutting performance and high segment wear?
Poor cutting performance and high segment wear in your Stihl Cordless Saw can occur if the abrasive wheel is turning in the wrong direction. Ensure that you mount the abrasive wheel so that it turns in the right direction.
Why does my Stihl Saw switch off during operation?
Your Stihl Saw might be switching off because the battery or machine electronics are too hot; remove the battery and allow both to cool off. It could also be due to an electrical malfunction; try removing and reinserting the battery to resolve this.
What to do if my Stihl Saw cuts out during operation?
If your Stihl Saw stops during use, it might be due to moisture in the tool or battery; let them dry. Overheating of the battery or tool electronics can also cause this; remove the battery and allow both to cool down. Another cause may be electric or electromagnetic interference; try removing and reinserting the battery.
Why does my Stihl Saw switch off while I'm using it?
If your Stihl Saw switches off during operation, it could be due to the battery or machine electronics overheating. Remove the battery and allow both the battery and the machine to cool off. Another cause might be an electrical or electromagnetic malfunction; in this case, remove the battery and reinsert it.
What to do if Stihl Cordless Saw has built-up edges?
If you notice built-up edges on your Stihl Cordless Saw, immediately "sharpen" the diamond abrasive wheel. You can do this by briefly cutting through an abrasive material such as sandstone, aerated concrete, or asphalt.
What to do if my Stihl TSA 230 Saw does not start?
If your Stihl Saw does not start, there could be several reasons. First, check for electrical contact issues between the machine and battery; remove the battery, inspect the contacts, and reinsert it. If the battery's charge is low (1 LED flashes green), charge the battery. If the battery is too hot or cold (1 LED is red), allow it to cool down or warm up to between 15°C and 20°C. For a battery fault (4 LEDs flash red), remove and reinsert the battery; if the LEDs continue to flash, the battery needs replacement. If the unit is too hot (3 LEDs are red), let it cool down. For electromagnetic malfunction (3 LEDs flash red), remove and reinsert the battery; if the LEDs still flash, the machine should be checked by a servicing dealer. Finally, if there's moisture, let the machine and battery d...
What to do if there are breakdowns in the Stihl Saw wheel?
If you are experiencing breakdowns or tears in the parent wheel and segment of your Stihl Saw, it is likely due to overloading. To resolve this, use a new abrasive wheel.
What to do if my Stihl TSA 230 has undercut?
If your Stihl Saw has undercut issues, it might be due to cutting in the wrong material. To fix this, use a new abrasive wheel and observe separating layers of various materials.
Why is the running time of my Stihl TSA 230 so short?
A short running time for your Stihl Saw could be caused by a battery that isn't fully charged; make sure to fully charge the battery. Alternatively, the battery's service life may have been reached or exceeded, requiring you to check and replace the battery.
What to do if my Stihl TSA 230 has ragged edges, crooked cut, no cutting performance, and generates sparks?
Ragged edges, crooked cuts, poor cutting performance, and sparks from your Stihl Saw can occur when the abrasive wheel is dull or has built-up edges (especially with abrasive wheels for stone). Sharpen abrasive wheels for stone by briefly cutting through abrasive materials, or replace the wheel.
Details on composite resin cutting wheels, types, and applications.
General| Power Source | Battery |
|---|---|
| Disc Diameter | 230 mm |
| Cutting Depth | 70 mm |
| Battery Type | Lithium-Ion |
| Battery Voltage | 36 V |
| Vibration level left/right | 3.5/3.5 m/s² |
To Next Page
