What does SSAM flash code three mean on my Sullair Air Compressor?
SSAM flash code three on your Sullair Air Compressor indicates a potential issue with the engine oil pressure switch. You should: * Check the wiring connection to the switch and tighten it if necessary. * Install a gauge in parallel with the switch. Replace the switch if the pressure exceeds 15 psig and stays open.
How to troubleshoot SSAM flash code two on a Sullair Air Compressor?
When your Sullair Air Compressor shows SSAM flash code two, this usually points to a problem with the engine coolant temperature. Here's how to troubleshoot: * Check the wiring connection to the engine coolant temperature switch and tighten it if necessary. * Check the switch continuity to ground and replace if necessary. * Ensure adequate cooling airflow by cleaning the cooler and verifying proper ventilation. * Inspect the fan belt; tighten or replace if loose or broken. * Check the engine coolant level and fill with the correct water/glycol mixture if low. * Change the water pump if it's faulty. * Replace the engine thermostat element if it's defective.
What to do if my Sullair Air Compressor shows SSAM flash code one?
If your Sullair Air Compressor displays SSAM flash code one, it indicates a potential issue with the compressor temperature. Here's what you should do: * Check the wiring connection to the compressor temperature switch and tighten it if it's loose. * Check the switch continuity to ground and replace it if necessary. * Ensure the receiver tank fluid level is adequate and add fluid if needed. * Inspect the fan belt for looseness or breakage, tightening or replacing it as required. * Address insufficient cooling airflow by cleaning the fluid cooler core and ensuring proper ventilation. * Change the fluid filter element if it's clogged. * Consider changing the fluid thermostat element if it's faulty. * If the fluid cooler tube is plugged internally, replace the cooler.
What causes improper unloading with excessive pressure build-up in Sullair 375H Air Compressor?
Improper unloading with excessive pressure build-up in your Sullair Air Compressor can result from: * A pressure regulating valve set too high; readjust it. * A control system leak causing loss of pressure signal; check control lines. * A defective pressure regulating valve; repair the valve (kit available). * An inlet valve jammed; free or replace the valve. * A restriction in the control system; check all control lines and components for ice or other contaminants. * A defective pressure relief valve that opens when the pressure is too low; replace the pressure relief valve. * A defective pressure regulator; check the diaphragm and replace it with a kit if necessary.
Why is my Sullair 375H Air Compressor not achieving full discharge pressure?
If your Sullair air compressor isn't reaching full discharge pressure, it could be due to: * The run/start valve not being in the run position (for compressors with idle warm-up controls, switch the valve to RUN). * Excessive air demand (check service lines for leaks or open valves). * A dirty air filter (check the filter and change the element if required). * A defective pressure regulator (check the diaphragm and replace with a kit if necessary). * A defective idle warm-up control (replace the control).
What does SSAM flash code three flashes mean on a Sullair Air Compressor?
If your Sullair Air Compressor shows SSAM flash code three flashes, it indicates the engine oil pressure switch is open. Check the wiring connection to the switch and tighten if necessary. Install gauge in parallel with the switch. Replace the switch if the pressure exceeds 15 psig and stays open. If the pressure is less than 15 psig, refer to the Engine Operator’s Manual.
What does SSAM flash code one flash mean on a Sullair 375H Air Compressor?
If your Sullair Air Compressor displays SSAM flash code one flash, it means the compressor temperature switch is open. Check the wiring connection to the switch and tighten it if loose. Also, check the switch continuity to ground and replace if necessary. If the compressor feels hot refer to COMPRESSOR OVERHEATING trouble shooting procedure.
General safety guidelines for operating and maintaining Sullair compressors.
Detailed procedures and warnings for safely towing the air compressor.
Precautions to prevent fire and explosion risks associated with the compressor.
Warnings and precautions regarding moving components of the compressor.
Precautions for handling toxic materials and compressed air safety.
Safety guidelines to prevent electrical shock when working with the compressor.
Safe practices for lifting and rigging the compressor unit.
Step-by-step instructions for safely jump-starting the compressor.
Procedures for safely controlling energy sources during maintenance.
Functional description of the single-stage, positive displacement rotary screw compressor.
Explanation of the system that maintains compressor temperature and lubrication.
Description of the receiver tank's functions and air/fluid separation.
How the control system regulates air intake based on demand.
Overview of controls and indicators on the compressor's instrument panel.
Explanation of codes displayed by the compressor shutdown system.
List of engine diagnostic trouble codes and their corrective actions.
Description of the system that monitors and manages compressor shutdowns.
Step-by-step guide for starting and shutting down the compressor for the first time.
Instructions for restarting the compressor after initial use.
Major service tasks to be performed every 1500 operating hours.
Detailed procedures for replacing key compressor components.
Guide to diagnosing and resolving common compressor symptoms and issues.
Prohibitions and acts considered tampering with noise control systems.
A list of recommended spare parts with part numbers and quantities.
General| Free Air Delivery | 375 cfm |
|---|---|
| Pressure | 150 psi |
| Model | 375H |
| Air Delivery | 375 cfm |
| Operating Pressure | 150 psi |
| Sound Level | 76 dBA |
| Type | Rotary Screw |
To Next Page
