EasyManua.ls Logo

Sulzer XJ Series - User Manual

Sulzer XJ Series
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Submersible Drainage Pump XJ (AT)
Submersible Drainage Center-line Pump XJC (AT)
Submersible Sludge Pump XJS (AT)
00833331AF 01.2016
www.sulzer.com
EN Starting and operating instructions 3
SV Start- och driftinstruktion 4
DE Inbetriebnahme- und Betriebsanleitung 5
FR Mise en service et utilisation 6
IT Instruzioni per l'avviamento e l'uso 7
ES
Instrucciones de puesta en marcha y funcionamiento
8
PT Instruções de arranque e operação 9
ET Käivitus- ja kasutusjuhised 10
DA Start- og driftsinstruktioner 11
FI Käynnistys- ja käyttöohje 12
EL Οδηγίεςεκκίνησηςκαιλειτουργίας 13
NL Start- en bedrijfstellingsaanwijzingen 14
NO Start- og driftsveiledning 15
BG
Ръководствозапусканевдействиеизаработа
16
CS
Pokynyprospuštěníaobsluhu
17
HR
Upute za puštanje u rad i korištenje
18
HU Indításiéskezelésiutasítások 19
LT
Užvedimoirnaudojimoinstrukcijos
20
LV Darbasākšanasunekspluatācijasnorādījumi 21
PL Instrukcja rozruchu i eksploatacji 22
RO
Instrucţiunidepornireşiutilizare
23
SI
Navodila za zagon in delovanje
24
SK
Pokynynaprevádzkuaobsluhu
25
TR
Çalıstırmaveişletmetalimatları
26
RU
Руководствопозапускуиэксплуатации
27
ZH
起动及操作说明
28

Table of Contents

Other manuals for Sulzer XJ Series

Preview: Workshop Manual
Workshop Manual36 pages

Questions and Answers

  • N
    nbowersAug 13, 2025
    Why does the motor of my Sulzer XJ keep tripping out?
    • L
      Lauren YangAug 14, 2025
      If your Sulzer Water Pump's motor trips out, several factors could be responsible: * The pump might be rotating in the wrong direction, in which case you should shift phases. * The water temperature may be too high (exceeding 40 ºC), so check the water temperature. * The impeller could be blocked; inspect for obstructions like stones or pieces of wood. * Low voltage may be the issue, possibly due to long cables or an inadequate power supply (like a generator). Therefore, you should check the cables and power supply.
  • D
    Dr. Jesse Cabrera Jr.Aug 19, 2025
    How to troubleshoot a Sulzer Water Pump that will not start?
    • B
      Brian JohnsonSep 12, 2025
      If your Sulzer Water Pump won't start, consider these potential causes: * Check the power lines to ensure they are not dead. * Inspect the fuses and breakers to see if any have blown. * Verify that there is no phase failure. * Look for obstructions like stones or wood that may be blocking the impeller. * A service inspection is needed if there is a loose cable.
  • G
    gadamsAug 25, 2025
    What causes the Residual Current Device to trip in a Sulzer Water Pump?
    • J
      John GloverAug 25, 2025
      If the Residual Current Device (RCD) trips out, it may be due to moisture in the stator. In this case, the motor needs to be dried.
  • D
    Dr. Lori HernandezAug 29, 2025
    What to do if my Sulzer XJ Water Pump is operating at too low capacity?
    • S
      Stephen GravesAug 29, 2025
      If your Sulzer Water Pump is operating at too low capacity, it might be because of: * A clogged strainer, which requires cleaning the strainer. * Sharp bends, folds, or restrictions in the discharge hose, so adjust the hose. * A total delivery head (static head + friction losses) that is too high, which means you should exchange the pump for one with sufficient capacity for the task.
  • B
    billy18Sep 3, 2025
    Why is there water in the oil chamber of my Sulzer XJ Water Pump?
    • S
      Susan BatesSep 3, 2025
      If you find water in the oil chamber of your Sulzer Water Pump, it could be caused by: * A defective shaft seal, which means you should change the primary seal. * Faulty assembly of o-rings, mechanical seal, or upper diffuser, in which case you should replace the parts. * Worn seals, so replace the parts and dry the motor.
  • D
    Donna MacdonaldNov 8, 2025
    What to do if water is inside the top cover or motor housing of my Sulzer XJ Water Pump?
    • J
      Justin BatesNov 8, 2025
      If water is found inside the top cover and/or motor housing of your Sulzer Water Pump, it could be due to several reasons: * A damaged or cut pump cable, which requires a cable replacement. * A loose cable gland or a faulty assembly of the gland, which means you should replace the cable gland and cable seal. * A damaged o-ring, foreign material between the motor housing and jacket, or cover, suggesting a complete pump overhaul and replacement of damaged parts. * Pinched wires between the top cover and main cover, indicating the need to replace damaged wires and check the contactor. * Loose or missing screws securing the top cover to the main cover, necessitating a complete pump overhaul and replacement of missing parts. * Water entered through the inspection hole, meaning you ...

Sulzer XJ Series Specifications

General IconGeneral
BrandSulzer
ModelXJ Series
CategoryWater Pump
LanguageEnglish

Related product manuals