Sumitomo Beier Variator Series User Manual

17
Table 10 Standard Lubrication System, BEIER part
Long-life grease series
A Type
BEIER
VARIATOR
BEIER size N02A N05A N1A N2A N3A N5A N8A N10A 15A 20A 30A 40A 50A
Forced lubrication type
Forced lubrication typeForced lubrication type
75A 100A 150A 200A
Horizontal Oil bath
Oil bath
N02B N05B N1B N2B N3B N5B N8B 10B 15B 20B 30B 50B 75B
Forced lubrication type
Forced lubrication typeForced lubrication type
100B 150B
Oil bath
Oil bath
N05D N1D N2D N3D N5D N8D N10D
Oil bath
Oil bath
Vertical
BEIER size
Horizontal
Vertical
BEIER size
Horizontal
Vertical
B Type
BEIER
VARIATOR
D Type
BEIER
VARIATOR
Lubricating oil cooling device is attached.
Refer to page 28.
Table 11 Standard Lubrication System, A Type and B Type BEIER-CYCLO Variator, CYCLO Part
Frame size
Horizontal
Grease
Oil bath
Grease
Oil bath Plunger pump (Self-lubrication)Vertical
6075 6095 6105 6125 6135 6145 6165 6175 6185 6195 6205 6215 6225 6235 6245 6255 6265 6275
Forced
lubrication
type
Single reduction
Frame size 6125DB
Grease
6130DB
6135DB
Grease
Oil bath
–187
Plunger pump (Self-lubrication)
–210 –289 –522 –522
210–
Grease
231– 319– 595– 649–
Grease
6130DC
6135DC
6160DA
6165DA
6160DC
6165DC
6170DC
6175DC
6180DB
6185DB
6190DA
6195DA
6205DA
6205DB
6215DA
6215DB
6225DA
6225DB
6235DA
6235DB
6245DA
6245DB
6255DA
6255DB
6265DA 6275DA
Forced lubirica-
tion type
Horizontal
Reduction
ratio
Reduction
ratio
Vertical
Double reduction
Long-life grease series
Table 12 Standard Lubrication System, D Type (ND Series) BEIER-CYCLO Variator, CYCLO Part (at standard input speed
by Table 13)
Frame size
Horizontal
Grease
Oil bath
Grease
Oil bath Plunger pump (Self-lubrication)Vertical
6095 6105 6125 6135 6145 6165 6175 6185 6195
Single reduction
Frame size 6125DB
Grease
6130DC
6135DC
Grease
Oil bath
104
Plunger pump (Self-lubrication)
– –165 –319 –377 –559
649–121–
Grease
104– 195– 377– 473–
Grease
6160DB
6165DB
6170DB
6175DB
6180DA
6185DA
6180DB
6185DB
6190DA
6195DA
6190DB
6195DB
6205DA
6205DB
6215DA
6215DB
6225DA
6225DB
6235DA
6235DB
6245DA
6245DB
6255DA 6265DA 6275DA
Forced lubirica-
tion type
Horizontal
Reduction
ratio
Reduction
ratio
Vertical
Double reduction
COMMON
8-2) Confirmation of Lubrication Method
• Refer to the applicable items regarding maintenance. Improper maintenance may decrcase unit life.
(1) Refer to Table 10–12 to confirm the gear lubrication method for your unit.
(2) Table 14 lists maintenance manual pages that can be referenced regarding lublication maintenance.
1. For models with trochoid pump, before start of Beier Variator or Beier-Cyclo Variator, start
pump motor and make sure there is mo abnormality in lubrication. Then start main motor. For
this requirement, interlock power supply for main motor with pump motor and give pump
motor a lead time of 30 to 60 seconds. Wire pump motor so that it will run in the specified
direction.
2. Oil filter (Fig. 12) is equiped on piping of forced lubrication type. Turn a handle on the oil filter
and take out clogging. At the beginning of operation, clean the filter once a day.
3. Discharge the sludge from drain plug at the bottom edge when the machine stops.
Fig. 12
Handle
Drain plug

Sumitomo Beier Variator Series Specifications

General

Brand	Sumitomo
Model	Beier Variator Series
Category	Engine
Language	English