Sunbeam EM4300 - Steam Wand and Group Head Maintenance

- Place Filter Basket into Group Handle
(without coffee) & insert into Group Head.
- Turn the DIAL to the ONE CUP setting.
Water will pour through.
- Return DIAL when finished.
- Repeat if needed.
Cleaning Steam Wand
• Every time
- After texturing milk purge the Steam Wand
by turning the DIAL to HOT WATER for just
1-2 secs.
- Wipe the Steam Wand with a damp cloth.
(See Operating Guide page 9)
• 2-3 Months
- Soak the Steam Wand overnight in the Milk
Jug with warm water & add one Sunbeam
Cleaning Tablet.
- In the morning remove the Jug & rinse
ensuring that all traces of the solution have
been removed.
- Wipe Steam Wand & Tip with a damp cloth
ensuring that all traces of the cleaning tablet
have been removed.
- Run Hot Water through the Steam Wand for
40 secs.
• Unblocking Steam Wand
- Insert the 'Steam' Cleaning Pin up the
Steam Wand Tip hole. (Cleaning Pin located in
the 'Accessories' storage area under the Drip
Tray).
- Run Hot Water through the Steam Wand.
• Steam Wand Remains Blocked:
- Unscrew the Steam Wand Tip & soak
overnight in the Milk Jug with warm water &
add one Sunbeam Cleaning Tablet.
- In the morning rinse the Jug & Steam Wand
Tip under running water ensuring all traces of
the cleaning tablet have been removed.
- Use the Cleaning Pin to clean the Steam Tip.
- Screw the Steam Wand Tip back into the
Steam Wand Arm.
- Run Hot Water through the Steam Wand for
40 secs.
ESPRESSO
MACHINE
CLEANING
TABLETS
PLEASE EMPTY TRAY
REMOVE
STEAM
FILTER
UNSCREW
INSERT
INSERT
D
U
A
L
W
A
L
L
ESPRESSO
MACHINE
CLEANING
TABLETS
T
H
E
R
M
O
B
L
O
C
K
5
8
M
M
C
A
F
É
G
R
O
U
P
H
E
A
D
I
N
S
E
R
T
ESPRESSO
MACHINE
CLEANING
TABLETS
PLEASE EMPTY TRAY
REMOVE
STEAM
FILTER
UNSCREW
INSERT
INSERT
D
U
A
L
W
A
L
L
ESPRESSO
MACHINE
CLEANING
TABLETS
T
H
E
R
M
O
B
L
O
C
K
5
8
M
M
C
A
F
É
G
R
O
U
P
H
E
A
D
I
N
S
E
R
T
19
Care & Cleaning
ESPRESSO
MACHINE
CLEANING
TABLETS
PLEASE EMPTY TRAY
REMOVE
STEAM
FILTER
UNSCREW
INSERT
INSERT
D
U
A
L
W
A
L
L
ESPRESSO
MACHINE
CLEANING
TABLETS
T
H
E
R
M
O
B
L
O
C
K
5
8
M
M
C
A
F
É
G
R
O
U
P
H
E
A
D
I
N
S
E
R
T
Group Head Rubber Seal
A rubber seal is located in the Group Head
and creates a seal against the Filter Basket
when making an espresso.
Over time this seal loses its elasticity and
may require replacement. The seal may
need replacing when watery espresso leaks
from around the Group Head, or if the Group
Handle feels loose when fully rotated to the
centre position.
Important: When your espresso machine
is not being used, we recommend that you
do not leave the Group Handle inserted
into the Group Head, as this will reduce
the life of the seal.
Note: Contact Sunbeam should you think
that the Group Head seal needs replacing.
Do not attempt to change the seal without
first consulting Sunbeam.
ESPRESSO
MACHINE
CLEANING
TABLETS
PLEASE EMPTY TRAY
REMOVE
STEAM
FILTER
UNSCREW
INSERT
INSERT
D
U
A
L
W
A
L
L
ESPRESSO
MACHINE
CLEANING
TABLETS
T
H
E
R
M
O
B
L
O
C
K
5
8
M
M
C
A
F
É
G
R
O
U
P
H
E
A
D
I
N
S
E
R
T