SunStar SPS SERIES - SPECIFICATIONS AND COMPONENTS; MODEL SPECIFICATIONS AND IDENTIFICATION; PACKING LIST AND ACCESSORY PACKAGES

Form 43343320
Dec 2017 -5-
5.0) SPECIFICATIONS
Model No.
Btu/hr
High
Input
(2-stage)
Btu/hr
Low
Input
Air Plate
Part #
Orifice Size
Minimum *
Mounting Height
Turbulator
Qty.
Natural Gas
Propane Gas
@
Horizontal
@
45º Angle
SPS/SPU 40
40,000
25,000
44140061
#32
(0.116)
#49
(0.073)
10 ft.
9 ft.
4
SPS/SPU 50
50,000
30,000
44140064
3.5mm
(0.138)
46
(0.081)
11 ft.
10 ft.
5
SPS/SPU 75
75,000
50,000
44140063
#21
(0.159)
2.5mm
(0.098)
13 ft.
12 ft.
5
SPS/SPU 100
100,000
65,000
44140062
#12
(0.189)
#32
(0.116)
14 ft.
13 ft.
3
SPS/SPU 125
125,000
80,000
44140066
#4
(0.209)
#30
(0.129)
14 ft.
13 ft.
7
SPS/SPU 150
150,000
100,000
44140067
“A”
(0.234)
#27
(0.144)
15 ft.
14 ft.
4
SPS/SPU 175
175,000
110,000
44140067
“E”
(0.250)
#23
(0.154)
16 ft.
15 ft.
0
SPS/SPU 200
200,000
125,000
44140068
6.9mm
(0.272)
4.1mm
(0.161)
18 ft.
16 ft.
1
* MOUNT HEATERS AS HIGH AS POSSIBLE. Minimums are shown as a guideline for human comfort and uniform
energy distribution for complete building heating applications. Consult your SunStar representative for the
particulars of your installation requirements.
Model Identification:
Control Option
Suffix
Gas Type
Description
N5
Natural
Single Stage Gas Valve – Single Stage Input
L5
Propane
Single Stage Gas Valve – Single Stage Input
N7
Natural
Two Stage Gas Valve – Modulating Input – High/Low Fire
L7
Propane
Two Stage Gas Valve – Modulating Input – High/Low Fire
Type
Gas
Gas Pipe
Connection
Tube
Diameter
Flue
Connection
1
Fresh Air
Connection
1
Electrical
Supply
Current
Rating
Natural
or Propane
½” MPT
(Male)
4”
4” Round
4” Round
120 Volt, 60Hz,
1 Phase
1.74 Amp
1
See Section 16.0) for vent sizes when multiple heaters are connected into a common vent
Module Electrical Rating:
Ignition System (direct spark):
Input-Control: 18-30 VAC 50/60 Hz (class 2 transformer)
Input Power-Line: 120 VAC (L1, IND contacts only)
Flame Sensitivity: 0.7 uA (microamps) minimum
15 second trial for ignition period
15 second pre-purge period
60 second inter-purge period
30 second post-purge period
3 tries for ignition (separate flame sensor).
6.0) PACKING LIST
A. SPS/SPU Burner Package
Part Description QTY
Burner Box Assembly (Refer to the following chart for Package Part Numbers) .......................... 1
4”ID x 4”Lg Flue Adapter Collar (#30504500) .................................................................................. 1
Fastener Kit – Burner Box Attachment/Flue Adapter Collar (#42907040) .................................. 1
Containing: #10 x 1/2” Self-Drilling Screws (#02189020) .................................................... 2
¼ - 20 Locknuts (#02167010) .............................................................................. 3
Tube Flange Gasket (#42921000) ........................................................................... 1
Turbulator 24” Long (#44152240) *See chart above for required quantities. .............................. *
Installation & Operation Instructions .................................................................................................... 1
Turnbuckle (#43343320) ......................................................................................................................... 1
Gas connector 5/8” OD x 36” (#30302360) – US only ....................................................................... 1
Screen Assembly 2-5/8” ID x 5-1/2” Long (#44151010) 200M BTU models only ....................... 1
End Reflector Package (#43341000) ................................................................................................... 1