SunStar SWF/C-UK1502 - Page 4

ii
7-4-4) REPETITION WORK .......................................................................................... 7-32
7-4-5) DATA SET-UP ..................................................................................................... 7-37
7-4-6) EMBROIDERY DESIGN EDITING ................................................................... 7-42
7-4-7) FRAME MOVEMENT ......................................................................................... 7-51
7-4-8) FLOAT (NON-STITCHING FUNCTIONS) ....................................................... 7-55
7-4-9) MACHINE DATA SET-UP ................................................................................. 7-56
7-4-10) THE FLOPPY FUNCTIONS ............................................................................. 7-60
7-4-11) MANUAL CUTTING ........................................................................................ 7-63
7-4-12) OFFSET SET-UP ................................................................................................ 7-63
7-4-13) NEEDLE BAR SELECTION ............................................................................. 7-65
CHAPTER 8 ERROR MESSAGES AND CORRECTION ..................................................................... 8-1
8-1) MAIN SHAFT MOTOR ........................................................................................................ 8-1
8-2) PULSE MOTORS ON X AND Y AXIS ............................................................................... 8-1
8-3) COLOR CHANGE ................................................................................................................. 8-1
8-4) ENCODER ............................................................................................................................. 8-2
8-5) REPETITION WORK ............................................................................................................ 8-2
8-6) FLOPPY DRIVE AND COMMUNICATION ...................................................................... 8-2
8-7) TAPE READER AND COMMUNICATION ....................................................................... 8-3
8-8) MEMORY .............................................................................................................................. 8-3
8-9) SYSTEM INSTALLATION .................................................................................................. 8-3
CHAPTER 9 THE CONTROL BOX ....................................................................................................... 9-1
9-1) CHANGING FUSE IN JOINT BOARD OF M/C WITH LESS THAN 12 HEADS ............ 9-1
9-2) CHANGING FUSE IN M/C WITH MORE THAN 12 HEADS ........................................... 9-3
9-3) STANDARD VOLTAGE FOR X, Y DRIVERS (BY MACHINE TYPE) ........................... 9-4
CHAPTER 10 MAINTENANCE AND INSPECTION ........................................................................... 10-1
10-1) CHECK POINTS FOR REGULAR INSPECTION .......................................................... 10-1
10-2) CLEANING ....................................................................................................................... 10-1
10-3) OIL SUPPLY ..................................................................................................................... 10-3
10-4) DRIVE BELT TENSION ................................................................................................... 10-8
CHAPTER 11 MACHINE ADJUSTMENTS .......................................................................................... 11-1
11-1) ADJUSTING THE TRIMMERS ....................................................................................... 11-1
11-1-1) ADJUSTING THE POSITION OF THE TRIMMING CAM
(INSERT ANGLE OF MOVABLE BLADE) .................................................... 11-1
11-1-2) ADJUSTING BLADE TENSION ...................................................................... 11-2
11-2) ADJUSTING THE TRIMMER RETURN SPRING ......................................................... 11-2
11-3) ADJUSTING UPPER THREAD HOLDING UNIT ...........................................................11-3
11-4) PICKER ADJUSTMENT .................................................................................................. 11-4
11-5) ADJUSTING UPPER THREAD HOLDER ...................................................................... 11-5
11-6) ADJUSTING LOW-NOISE PRESSER FOOT .................................................................. 11-6
11-7) RELATIONSHIP BETWEEN PRESSER FOOT AND NEEDLE .................................... 11-7
11-8) CORRECT POSITION OF NEEDLE ................................................................................ 11-8
11-9) ADJUSTING HALF-TURN FILM FOR COLOR CHANGE ........................................... 11-9
11-10) ENCODER ADJUSTMENT ............................................................................................ 11-9
11-11) JUMP MOTOR ADJUSTMENT ................................................................................... 11-10
11-12) ADJUSTING DRIVE BELT TENSION ........................................................................ 11-11
11-12-1) Y-AXIS TIMING BELT ................................................................................. 11-11
11-12-2) X-AXIS TIMING BELT ................................................................................. 11-12
11-12-3) TIMING BELT ON MAIN SHAFT MOTOR ................................................ 11-12
11-13) LAMP (OPTIONAL) ..................................................................................................... 11-13
CHAPTER 12 TROUBLESHOOTING ................................................................................................... 12-1
CHAPTER 13
BLOCK DIAGRAM ........................................................................................................ 13-1