Supermicro X10DRL-CT - I-SGPIO1;2 Headers; Standby Power Header

2-30
X10DRL-CT/-iT/-C Motherboard User’s Manual
SAN MAC
BIOS LICENSE
SAS CODE
MAC CODE
IPMI CODE
BAR CODE
UID
LEDPWR
LEDBMC
JUSBRJ45
FAN6
FAN5
FAN1
FANB
FAN2
FAN3
FAN4
FANA
JIPMB1
JNVI2C1
JVRM2
JPTG1
1
JPB1
3
JPF1
JPF2
JPG1
JBR1
JPME2
JI2C1
JI2C2
JPS1
JPL2
JPL1
JVRM1
JWD1
J24
1
13
1224
1
J7J5
JS18
JF1
JPWR2
JPWR1
1
JL1
J21
JPI2C1
24
JPS7
SP1
BT1
+
JLAN3
JUIDB1
JSD1
JS1
JSTBY1
I-SGPIO1
I-SGPIO2
J25
JTPM1
JVGA
JLAN1
JBT1
I2C BUS FOR PCI-E SLOT
1-2:ENABLE
2-3:DISABLE
X10DRL-CT
DESIGNED IN USA
REV:1.00
CHASSIS INTRUSION
JL1
2-3:DISABLE
1-2:ENABLE
JI2C1/JI2C2
1-2:NORMAL
2-3:BIOS RECOVERY
JBR1
2-3:ME MANUFACTURING MODE
JPME2
1-2:NORMAL
1-2 ENABLE
JPL2 LAN
2-3 DISABLE
JPL1/
JPI2C1:PWR I2C
JPG1:VGA
JPB1:BMC
2-3 DISABLE
1-2 ENABLE
2-3 DISABLE
1-2 ENABLE
JPTG1:10Gb LAN
2-3 DISABLE
1-2 ENABLE
JPS1:SAS
L-SAS0-3
L-SAS4-7
USB8/9(3.0)
PCI-E 3.0 X8
LAN4
LAN3
LAN1
USB12/13(3.0)
I-SATA0
I-SATA1
I-SATA2
I-SATA3
USB2/3
USB4
JTPM1:TPM/PORT80
CHASSIS INTRUSION
I-SATA4
CMOS CLEAR
I-SATA5
CPU2 SLOT4
SPEAKER-PIN 4-7
JD1:
PWR LED-PIN 1-3
2-3:NMI
JWD1:WATCH DOG
1-2:RST
CPU1 SLOT5 PCI-E 3.0 X16
CPU1 SLOT6 PCI-E 3.0 X8
RSTPWR
ON
JF1
P1-DIMMD1
P1-DIMMC1
X NICOH/
2FF
HDDNIC
LED1
PWR
LED
NMIX
P2-DIMMF1
P2-DIMME1
CPU2
VGA
CPU1
P1-DIMMB1
P1-DIMMA1
P2-DIMMH1
P2-DIMMG1
COM1
IPMI_LAN
LAN2
JD1
A
B
A. I-SGPIO1
B. I-SGPIO2
C. Standby PWR
I-SGPIO1/2 Headers
Two SGPIO (Serial Link General Pur-
pose Input/Output) headers are locat-
ed on the motherboard. I-SGPIO1/2
support onboard I-SATA0-5 connec-
tions. See the table on the right for
pin denitions.
Note: NC= No Connection
I-SGPIO Headers
Pin Denitions
Pin# Denition Pin Denition
1 NC 2 NC
3 Ground 4 Data
5 Load 6 Ground
7 Clock 8 NC
C
Standby Power Header
The +5V Standby Power header is
located at JSTBY1 on the mother-
board. See the table on the right for
pin denitions. (You must also have a
card with a Standby Power connector
and a cable to use this feature.)
Standby PWR
Pin Denitions
Pin# Denition
1 +5V Standby
2 Ground
3 No Connection
I-SGPIO0/1 & S-SGPIO Support
I-SGPIO1 I-SATA Ports 0/1/2/3 Supported
I-SGPIO2 I-SATA Ports 4/5 Supported