System Sensor FSB-200S - User Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS
FSB-200, FSB-200S
Single-ended Reflected Type
Projected Beam Smoke Detector
12 Clintonville Rd.
Northford, CT 06472-1653
Phone: 203/484-7161
N200-25-00 1 I56-2424-04R
Specifications
General
Range: 16 to 230 Feet (5 to 70m)
230 to 328 Feet (70 to 100m) using optional accessory BEAMLRK
Sensitivity: 25% to 50% Total Obscuration in 6 levels
Level 1 = 25%
Level 2 = 30%
Level 3 = 40%
Level 4 = 50%
Level 5 = 30% to 50% (Acclimate)
Level 6 = 40% to 50% (Acclimate)
Spacing: 30 to 60 Feet (9.1 to 18.3m)
Response Time: Alarm: 20 seconds typical
Trouble: 30 seconds typical
Trouble Conditions: Beam Blockage (96% or More Obscuration)
Improper Initial Alignment
Self-compensation limit reached (service needed)
In Alignment mode
Test/Reset Features: Integral Sensitivity Test Filter (FSB-200S only, requires additional external power supply)
Sensitivity Filter (Incremental scale on reflector)
Local Alarm Test Switch
Local Alarm Reset Switch
Remote Test and Reset Switch Capability
(compatible with RTS451/RTS451KEY)
Indicators: Alarm: Remote Output, Local LED (red)
Trouble: Remote Output, Local LED (yellow)
Blink Pattern Indicates Trouble Diagnostics
Normal Operation: Local LED (flashing green with communication)
Alignment Aids: Optical Gunsight (coarse adjustment)
00 to 99 Digital Display (fine adjustment)
Sensitivity: Digital Display Readout in Percent Obscuration
Style 7 Operation: On-board isolators provide style 7 operation.
(may be disabled via shunts on circuit board)
Environmental
Temperature: –22°F to 131°F (–30°C to 55°C)
Note: for applications below 32°F (0°C) see Special Applications section of this manual.
Humidity: 10% to 93% RH Noncondensing
Mechanical
Shipping Weight: 3.9 lbs. (1.77 kg)
Shipping Size: 15″ × 10.5″ × 6.5″ (381mm × 267mm × 165mm)
Mounting: Wall only without optional accessories
Wiring: Plug-in Terminal Blocks (12 to 22AWG)
Adjustment Angle: ±10° Horizontal and Vertical
Paintable Trim Ring: May be painted using enamel or acrylic type paints

System Sensor FSB-200S Specifications

General

Brand	System Sensor
Model	FSB-200S
Category	Smoke Alarm
Language	English

Summary

Product Specifications

General Specifications

Details on range, sensitivity levels, response times, trouble conditions, indicators, and style 7 operation.

Environmental and Mechanical

Environmental limits, shipping details, mounting, wiring, and painting guidelines for the detector.

Electrical and Application Details

Electrical Specifications

Electrical requirements, current draw, external supply, and remote output specifications for the detector.

General Description and Special Applications

Overview of the beam smoke detector's function and its suitability for various challenging environments.

Accessories and Detector Placement

Approved Accessories

Details on optional accessories like BEAMLRK, BEAMMMK, BEAMSMK, BEAMHK, BEAMHKR.

Detector Placement Guidelines

Guidance on optimal placement of beam smoke detectors considering room features and codes.

Spacing and Mounting

Spacing Guidelines

Recommended spacing for beam detectors on smooth and sloped ceilings.

Mounting Considerations and Instructions

Advice on selecting mounting surfaces and detailed steps for installation.

Wiring and Installation Procedures

Wiring Installation Guidelines

Best practices for wiring installation, including compliance with codes and proper connection techniques.

Wiring Diagrams

Visual guides for detector wiring, including remote test station connections.

Installation and Alignment Process

Pre-Alignment Checklist and Coarse Alignment

Essential checks and initial alignment steps for the detector and reflector.

Fine Adjustment and Final Verification

Fine-tuning optics, final gain adjustment, and verification of detector setup.

Detector Controls and Sensitivity Settings

Switch and Adjustment Locations

Identification of switch controls, alignment adjustments, and housing screw locations on the detector.

Sensitivity Selection

Guide to selecting detector sensitivity based on distance and environmental conditions.

Sensitivity Testing and Maintenance

Sensitivity Testing Procedures

Procedures for testing detector sensitivity using calibrated filters or the test switch.

Maintenance and Painting

Instructions for cleaning the detector and painting the aesthetic ring.

Operational Modes and Troubleshooting Guide

Operation Modes

Overview of different detector operating modes and their corresponding LED and output indications.

Troubleshooting Guide

Common issues, causes, and troubleshooting tips for detector faults and alarms.

Installation Templates and FCC Statement

Detector Drilling Template

A scale 1:1 template for drilling mounting holes for the detector unit.

FCC Statement

Statement regarding the detector's compliance with FCC rules for digital devices.