INTRODUCTION
The LT-200 FL01 Series is part of the Fire Alarm Aspiration Sensing
Technology
®
(FAAST) family. FAAST is an advanced re detection
system for use where early warning and very early warning are a
requirement. The system continuously draws air from the controlled
environment through a series of sampling holes to monitor the
environment for smoke particulate.
The FL01 is the stand-alone version of the FAAST LT-200 range and is
available in 3 dierent models:
FL0111E-HS - Has single channel capability with one high sensitivity
smoke sensor.
FL0112E-HS - Has single channel capability with two high sensitivity
smoke sensors in a common chamber for coincidence detection.
FL0122E-HS - Has two channel capability with two high sensitivity
smoke sensors in separate chambers. (One sensor for each channel).
This guide provides information for mounting the unit, basic installation
and advice on pipe layout designs, together with an overview of
using the PipeIQ™ software (version 2.9.1 or higher) to achieve
EN54 compliant designs. For more complex designs using increased
functionality (experienced users only) please see the FAAST LT-200
Advanced Setup and Control Guide - reference D200-100-01.
Important Note
Aspirating Smoke Detectors supplied and installed within the EU must
conform to the EU Construction Products Regulation (CPR) 305/2011
and the related European Product Standard EN 54-20. FAAST LT-200
has been tested and certied to ensure that it conforms to the necessary
Standards, but strict adherence to this instruction guide is advised to
ensure that the installation meets the requirements of the CPR.
The PipeIQ™ software (use version 2.9.1 or higher) is a design
application to help a user create or verify EN54 compliant pipe layouts,
and to allow conguration of the FAAST LT-200 unit.
Warning
The performance of this system is dependent upon the pipe
network. Any extension or modication to the designed installation
may cause improper operation. The operational eects of such
changes need to be veried using the PipeIQ design software.
This equipment and all associated pipe work must be installed in
accordance with all relevant codes and regulations.
PARTS LIST
Description Quantity
FAAST LT-200 unit 1
Mounting bracket 1
3-pin Terminal block 6
4-pin Terminal block 1
2-pin Terminal block 3
47 k-ohm EOL Resistor 2
USB Cable 1
Front Panel Labelling Pack 1
Wiring Diagram Label 1
Installation Kit USB Pen Drive 1
Quick Installation Guide 1
SPECIFICATIONS
Electrical Characteristics
Voltage Range: 18.5 - 31.5 VDC
Supply Current: 1 Channel: 170mA (typical); 360mA (max) @ 24
VDC 25
o
C (excluding sounders)
2 Channel: 270mA (typical); 570mA (max) @ 24
VDC 25
o
C (excluding sounders)
Congurable Input: Activation Time: 2s (min)
Relay Contact Ratings: 2.0 A @ 30 VDC, 0.5A @ 30 VAC
Environmental Ratings
Temperature: -10°C to 55°C
Relative Humidity: 10% to 93% (non-condensing)
Flow Fault: ± 20% of the reference ow
IP Rating: 65
Mechanical
Exterior Dimensions: See Figure 1
Wiring: 0.5 mm² to 2 mm² max
Maximum Single Pipe Length: 100m (Class C)
Maximum Branched Pipe Length: 160m (2 x 80m, Class C)
Maximum Number of Holes: See Table 1A
Pipe Spec (EN54-20 Compliance): to EN 61386
(Crush 1, Impact 1, Temp 31)
Outside Pipe Diameter: 25mm (nom) or 27mm (nom)
Shipping Weight: 6.5kg (inc sensors)
Fire Alarm Aspiration Sensing Technology
®
FL0111E-HS FL0112E-HS FL0122E-HS
STAND-ALONE FAAST LT-200 MODELS
QUICK INSTALLATION GUIDE
ENGLISH
CONTENTS
Introduction 1
Parts List 1
Specications 1
Physical Installation 2
Front panel labels 2
Mounting to the wall 2
Pipe hole conguration 3
Exhaust pipe 4
Wiring Installation 4
Terminal designations 5
Relays 5
External reset 6
Front Panel 6
Indicators and fault descriptions 7
Buttons 7
Testing 8
Service 8
PipeIQ™ Software 9
Appendix A -
PipeIQ™ and Pipe System Design 10
Appendix B -
Practical Pipe Designs 11
To Next Page
Need help?
General
