System Sensor FSB-200 User Manual

INSTALLATION AND MAINTENANCE INSTRUCTIONS
FSB-200, FSB-200S
Single-ended Reflected Type
Projected Beam Smoke Detector
12 Clintonville Rd.
Northford, CT 06472-1653
Phone: 203/484-7161
N200-25-00 1 I56-2424-04R
Specifications
General
Range: 16 to 230 Feet (5 to 70m)
230 to 328 Feet (70 to 100m) using optional accessory BEAMLRK
Sensitivity: 25% to 50% Total Obscuration in 6 levels
Level 1 = 25%
Level 2 = 30%
Level 3 = 40%
Level 4 = 50%
Level 5 = 30% to 50% (Acclimate)
Level 6 = 40% to 50% (Acclimate)
Spacing: 30 to 60 Feet (9.1 to 18.3m)
Response Time: Alarm: 20 seconds typical
Trouble: 30 seconds typical
Trouble Conditions: Beam Blockage (96% or More Obscuration)
Improper Initial Alignment
Self-compensation limit reached (service needed)
In Alignment mode
Test/Reset Features: Integral Sensitivity Test Filter (FSB-200S only, requires additional external power supply)
Sensitivity Filter (Incremental scale on reflector)
Local Alarm Test Switch
Local Alarm Reset Switch
Remote Test and Reset Switch Capability
(compatible with RTS451/RTS451KEY)
Indicators: Alarm: Remote Output, Local LED (red)
Trouble: Remote Output, Local LED (yellow)
Blink Pattern Indicates Trouble Diagnostics
Normal Operation: Local LED (flashing green with communication)
Alignment Aids: Optical Gunsight (coarse adjustment)
00 to 99 Digital Display (fine adjustment)
Sensitivity: Digital Display Readout in Percent Obscuration
Style 7 Operation: On-board isolators provide style 7 operation.
(may be disabled via shunts on circuit board)
Environmental
Temperature: –22°F to 131°F (–30°C to 55°C)
Note: for applications below 32°F (0°C) see Special Applications section of this manual.
Humidity: 10% to 93% RH Noncondensing
Mechanical
Shipping Weight: 3.9 lbs. (1.77 kg)
Shipping Size: 15″ × 10.5″ × 6.5″ (381mm × 267mm × 165mm)
Mounting: Wall only without optional accessories
Wiring: Plug-in Terminal Blocks (12 to 22AWG)
Adjustment Angle: ±10° Horizontal and Vertical
Paintable Trim Ring: May be painted using enamel or acrylic type paints

System Sensor FSB-200 Specifications

General

Brand	System Sensor
Model	FSB-200
Category	Smoke Alarm
Language	English

Summary

Product Specifications

General Specifications

Details on range, sensitivity, spacing, response time, trouble conditions, indicators, environmental, and mechanical aspects.

Electrical Specifications

Covers voltage, standby current, alarm current, trouble current, alignment current, and external supply details.

General Description and Special Applications

General Description

Explains the long-range projected beam smoke detector and its basic operation.

Special Applications

Discusses suitability for challenging environments like high ceilings, dust, and temperature extremes.

Installation Components and Guidelines

Approved Accessories

Lists and describes accessories like BEAMLRK, BEAMMMK, BEAMSMK, BEAMHK, BEAMHKR.

Detector Placement

Guidance on where to position beam detectors for optimal protection and compliance.

Mounting Locations

Criteria for selecting stable mounting surfaces and avoiding vibration for detector installation.

Mounting Instructions

Step-by-step guidance for mounting the transmitter/receiver unit and reflector securely.

Wiring Installation Guidelines

Details on compliance, wire gauge, conduit, grounding, and connection methods for proper wiring.

Alignment and Sensitivity Configuration

Pre-Alignment Checklist

Essential checks before starting the alignment process to ensure proper setup and avoid issues.

Coarse Alignment

Initial adjustment to roughly align the detector and reflector using optical sights.

Fine Adjustment

Detailed optical tuning using the digital display to maximize signal strength.

Final Gain Adjustment

Final electronic gain adjustment with the detector housing installed for optimal performance.

Final Verification

Testing the detector's response to smoke and ensuring correct sensitivity settings after alignment.

Sensitivity Selection

How to choose the appropriate sensitivity setting based on distance and environmental factors.

Testing and Maintenance

Sensitivity Testing

Procedures for verifying detector sensitivity using calibrated test filters or manual blockage.

Test Switch Operation

Using local and remote test switches to initiate alarm or trouble conditions for verification.

Maintenance Procedures

Guidelines for cleaning the detector and reflector to ensure continued reliable operation.

Painting Guidelines

Instructions for painting the detector's outer aesthetic ring.

Smoke Detector Guards

Information on the use of detector guards with this model.

Operational Information and Appendices

Operation Modes and Troubleshooting Guide

Detailed table of detector modes, LED indications, and troubleshooting tips for various conditions.

Detector Drilling Template

A full-scale template for drilling mounting holes for the detector.

Reflector Drilling Template

A full-scale template for drilling mounting holes for the reflector.

FCC Compliance Statement

Statement regarding compliance with FCC rules for digital devices and potential radio interference.