EasyManua.ls Logo

Taylor QS11 - User Manual

Taylor QS11
43 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Models QS11/23
Modular Grills
Original Operating Instructions
074606--M
5/24/04 (Original Publication)
(Updated 3/4/13)

Other manuals for Taylor QS11

Questions and Answers

  • S
    Samantha CollinsAug 18, 2025
    What to do if the grease drawer on my Taylor QS11 Grill won't close?
    • C
      Cindy MorganAug 18, 2025
      If the grease drawer of your Taylor Grill will not close, it's likely due to product buildup in the back of the grease partition. Refer to the “Cleaning the Grease Tray Partition” instructions.
  • S
    Samantha KingAug 21, 2025
    Why is my Taylor QS11 not heating up?
    • J
      james01Aug 21, 2025
      If your Taylor Grill isn't heating, there are several things you can check: * First, ensure the power cord is properly connected. * Next, check if a circuit breaker has tripped and reset it if necessary. * Also, verify that the power switch is in the ON position. If these steps don't resolve the issue, the power switch, relay, or relay board might be faulty, and it's best to contact a service technician.
  • S
    salasjeffreyAug 23, 2025
    How to fix undercooked or overcooked food on Taylor QS11 Grill?
    • S
      Sarah OlsonAug 23, 2025
      If your product is undercooked, overcooked, or cooking unevenly on the Taylor Grill, consider the following: * Replace the release material sheet if it's worn. * Adjust the cooking time, temperature setting, and gap as needed. * Ensure the correct item is selected and the temperature is properly calibrated. * Make sure the cook surfaces are parallel; otherwise, contact a service technician or refer to the leveling procedures. * Load and remove the product in the same order, ensuring it's fully under the top plate. Also, make sure that you followed closing procedures to remove carbon build-up. If a heat zone isn't heating, contact a service technician.
  • C
    Caitlyn WilliamsAug 26, 2025
    Why is grease dripping from under the grease drawer of my Taylor QS11?
    • B
      Brian WilliamsAug 26, 2025
      If grease is dripping from under the grease drawer of your Taylor Grill, the grease tray is likely full. Empty the grease tray.
  • S
    scott14Aug 27, 2025
    Why won't the upper cook surface stay raised on my Taylor QS11?
    • A
      Amanda BatesAug 27, 2025
      If the upper cook surface of your Taylor Grill will not stay in the raised position, it is probably caused by defective gas filled cylinder(s). Contact a service technician.
  • K
    Kari DuncanAug 30, 2025
    Why is my Taylor QS11 product under-cooked, overcooked, or cooking unevenly?
    • E
      Edward SmithAug 30, 2025
      Several factors can cause uneven cooking. The release material sheet might be worn and needs replacement. The cooking time, temperature setting, or gap setting may be incorrect and require adjustment. Ensure the heat zone is working, and address any carbon build-up on the upper cook surface by following closing procedures. Select the correct item and calibrate the grill if the temperature calibration is off. If the cook surfaces aren't parallel, contact a service technician to level the grill. Always load and remove the product in the same order, ensuring it's fully under the top plate.
  • J
    Julie StoneSep 1, 2025
    What to do if Taylor Grill will not heat?
    • M
      Margaret RochaSep 1, 2025
      If your grill isn't heating, first check the power cord connection and ensure it's properly connected. Then, check the circuit breaker and reset it if it has tripped. Finally, make sure the power switch is in the ON position. If the issue persists, it may be due to a faulty power switch, relay, or relay board, and you should contact a service technician.
  • C
    connerdaveSep 3, 2025
    What to do if grease drips from under the grease drawer of my Taylor Grill?
    • M
      Michael HenrySep 4, 2025
      If grease is dripping from under the grease drawer, the grease tray is likely full. Empty the grease tray to resolve this issue.
  • J
    Jessica RussellSep 6, 2025
    What to do if one heat zone will not heat on my Taylor Grill and the indicator light is not on, with the display flashing “TOO COOL”?
    • M
      Mark WrightSep 6, 2025
      If one heat zone isn't heating and the indicator light is off while the display flashes “TOO COOL”, first check the temperature setting to ensure the control is correctly set. If the problem persists, it could be due to a faulty relay, relay board, thermocouple, or a unit fault. If the unit displays a fault, clear it. If clearing the fault is ineffective, contact a service technician.
  • A
    alison81Sep 8, 2025
    What to do if one heat zone will not heat on my Taylor QS11, and the indicator light is on, with the display flashing “TOO COOL”?
    • C
      Christine ByrdSep 8, 2025
      If one heat zone isn't heating, but the indicator light is on and the display flashes “TOO COOL”, the heater, thermocouple, thermo overload, relay, or relay board may be faulty. Another possibility is that the unit displays a fault. Clear the fault. If the action is ineffective, contact a service technician.

Taylor QS11 Specifications

General IconGeneral
ModelQS11
CategoryGrill
TypeGas Grill
Power SourceGas
Fuel TypePropane

Related product manuals