To Next Page
A
Alejandro WaltonAug 17, 2025
How to fix no sound issue on TC Electronic Music Equipment?
- JJustin JohnsonAug 17, 2025
If there is no sound, and Killdry in the I/O setup is set to ON while the unit is bypassed, ensure that Killdry is set to OFF.
How to fix no sound issue on TC Electronic Music Equipment?
If there is no sound, and Killdry in the I/O setup is set to ON while the unit is bypassed, ensure that Killdry is set to OFF.
What to do if TC Electronic Music Equipment doesn't turn off with the power switch?
If you cannot turn off the power with the power switch, press and hold the switch for at least 1 second. This delay prevents unintended power offs.
What to do if TC Electronic Music Equipment display is blank?
If the display is blank and you cannot run the application software, enter the SOFTWARE BOOT menu by keeping the ENTER button pressed at power on. Then, dial the option to INFO and press ENTER to check the application software. If it is corrupted, reload the application software.
Why is the right input meter not showing any signal on my TC Electronic Music Equipment?
If the right input meter is not showing any signal, check if 'L-Only' is selected in the I/O Setup within the Audio menu.
How to fix lines or spots on TC Electronic Music Equipment display?
If you observe lines or spots on the display or the backlight is blinking, first ensure that no external equipment is influencing the display with magnetic or hot fields. If the distortion persists, replace the display. If the backlight is bad or blinking, inspect the soldering on the display, especially the two connections going to the upper part of the display.
What to do if I still have problems with presets made in version 1.05 after installing a new software version on my TC Electronic Music Equipment?
If you continue to experience issues with presets created in version 1.05 after a software update, recall the affected preset and save it to a new preset number. Alternatively, you can save all presets to a card and then perform a master reset, loading the presets afterward.
How to resolve 'Invalid software' message when loading software from G-Card on TC Electronic Music Equipment?
To resolve the 'Invalid software' message when loading from a G-Card: 1. Insert the G-Card. 2. Power on using the front switch. 3. When 'CARD ACCEPTED' appears, power off. 4. Quickly press ENTER while powering on again to access the boot menu. 5. Press ENTER again to load the software, which takes about 15 seconds.
What does the message 'User Preset Error, Cleared All Presets' mean on TC Electronic Music Equipment?
The message 'User Preset Error, Cleared All Presets' normally appears during the first power up after a RESET. It indicates that all presets have been set to the factory default.
What to do if analog in/out fails on TC Electronic Music Equipment?
If the analog in/out fails, try using different cables. When connecting analog in/out to unbalanced equipment, ensure that XLR pin 3 is connected to pin 1. If IC35 and IC36 are defective, replace them with type MC33079.
What to do if digital or MIDI in/out fails on TC Electronic Music Equipment?
General| Type | Multi-effects processor |
|---|---|
| Number of Effects | Up to 12 simultaneous effects |
| Sampling Rate | 44.1 kHz |
| Bit Depth | 24-bit |
| A/D Resolution | 24-bit |
| D/A Resolution | 24-bit |
| Frequency Response | 20 Hz - 20 kHz |
| THD+N | <0.005% |
| Effects Types | Reverb, Delay, Chorus, Flanger, Phaser, Pitch Shifter, EQ |
| Inputs | 2 x 1/4" |
| Outputs | 2 x 1/4" |
| MIDI | In/Out |
| Digital I/O | S/PDIF |
| Dimensions | 19" x 1.75" |
| Weight | 5.5 lbs |
