Technics SA-1000 - Page 12

)
“on”
position.
(put
Geman
broadcast
reception
or
y
} Adjust volume level (7).
’ Pick-up:
Place pick-up on disc surface;
performance will begin.
Speed selector: a speed.
Push (#1—~ m)_
“MAIN” or “REMOTE”.
(Refer to note 3.)
**ON’’ position.
;
-
Set
to
“F
AUTO”
for
FM
broadca
(Set
to
“AM”
for
AM
broadc
sts.
Set volume ‘control to. low ae
position tCY 00-36" for
Baler tunings rece
° + Signal-strength. meter:
Best reception is at”
Adjust volume __ point where. indication’
needle is farthest to
right.
ame raliare! meter: ue
Then best FM. reception
(mountainous
7
egion,
=
~~
—(least-distortion)
is-
af
~
etc.) 4
}
point where indication
needle is iu center.
Set to (H—m) “ON" if noise is”
excessive in high SOU nd range ot
layb ake button:
AUK) aa) F- WYaet- (ol am ol 0] role down;
performance will begin, .
Tape
selector:
py
Te
‘Set
tape’
selector
to
type
of
tape
being
used.
D insert cassote (with side to- >be ite
Played. fA: (oe) a FB) upward).
Steps required for all operations
: To listen through headphones
e > To use equip pment connected to
(Follow these steps, as necessary, for all operations after adjustment of volume level.)
“Technics
Release speaker selectors: (mB)
mB ome)ii position y when repeaker: FTolUlalon
is not WE Lal (-JeB
. jth position.
El s on rear panel, operate in same
way as. described in the section “To TS cul
ie com -(e (of ol der- (olor: (-] ame
elf atape deck is connected fe) “AUX”
| terminals. folain d=y-\ panel, operate in same
S described in 1 the section ‘To listen
a
When
output
level
is
low,
push
(l—
ie)
X0.1’’
or
‘*X0.01”’
power
display
range
|
selector
for
an
output
level
indication.
by
the
power
indicators
10
or
100
times:
higher.
Miaedty ch eeihenneeg emery SARE Str mnttwernae: emits A Be tae Rae
Oe Re aa
“ djus one quality as ol-) i dor
Use
only
for
recording.
(Refer
:
4
'
‘Set
to
“
—20
dB"
to
de
rease
volume
quickly.
3
to page 5. )
Low-range
sound
is
adjusted
with
bass
cpntrol
|
phono
motor
Tumble
and
other
fow-range
(“BASS”), mid-range sound with mid-range
control (‘MID RANGE’), and high-range
saund with treble contro} (“TREBLE
noise, set left one to ‘30. Hz’ position. a.
To eliminate noise caused by dust on. disc, and
other high-fange 1 noise, “Set right one to”
Adjust
left/right
volume
balance.
=
Set roma (0) \(@ Maan Come: (e | UI iecarelais volume
4 balance ols hs listen monaurally.
Use only for recording. (Refer. |
to page 9.) .
Set to “ON” when listening: at low volume ie
level.
} When. set to “OFF”, ch ie wile.
‘flat’? regardless of setting of tone contro
cand boost/filter selectors.
(Note: No effect upon filter function 8) boost/filter
selectors at. either position.)
After
performance
is
finished,
power
switches
of
all
equipment
should
be
turned
“OFF.