Technics SA-1000 - Tape-To-Tape Recording

TAPE RECORDING
When the recording-mode_ selector@ is set to the
“SOURCE” position, the signal source selected by the input
selectordd is emitted from the tape deck 1 and 2 recording
output terminalis (“REC OUT’).
1) Set the recording-mode selector to the “SOURCE” po-
Sition.
Set the input selector@ to the position corresponding to
the program source to be recorded.
3) Adjust the recording levei of the tape deck, and begin the
recording.
2
——
To record to tape deck 1 or 2, or to both simultaneously
8-track stereo tape deck etc.
(playback only}
=
=
es
——
("TAPE2 ')
(OVARG IJ terminals
terminalis
Q) 2
"Sy. SOURCEISOUACE 6
i 21
Tape deck 1 =
| Tape deck 2
Wages Test
PLAYBACK lozatey
: [eee
| DIN (REC/PLAY)
_) terminal
Speaker
S$ 1~S2 Recording-mode selector
$3 Tape-monitor selector 45)
TAPE-TO-TAPE RECORDING
If two tape decks are connected, recordings can be made
from one deck to the other. |
Notes:
@ To record from tape deck 1 to 2, or from 2 to 1:
1) Set the recording-mode selector@ to the ‘TAPE 1p>2”’
position.
(To record from tape deck 2 to tape deck 1, set the record-
ing-mode selector@ to the ‘‘TAPE 21” position.)
2) Prepare tape deck 1 (or tape deck 2) for playback, and
tape deck 2 (or tape deck 1) for recording, and begin the
tape-to-tape recording.
To record from tape deck 1 to 2
8-track stereo tape deck etc.
(playback only)
(‘TAPE 2°)
terminals
Tape deck 2
| DIN (REC/PLAY)
_J terminal
Speaker
Notes: S 1i~S2 Recording-mode selector 46
$3 Tape-monitor selector 4
I To listen to phono discs or a radio broadcast while
recording from tape to tape:
By setting the tape-monitor selector@ to the ‘‘SSOURCE”
position, it is possible to listen to phono discs or a radio
broadcast while recording from tape to tape.
TAPE MONITORING
If the tape deck to be used is the three-head type, tape
monitoring is a method to listen to, and thus confirm, the
material being recorded.
When the tape-monitor selector@ is set to the ‘‘“SOURCE”’
position, the incoming sound can be heard immediately
prior to recording. When it is set to the ‘‘TAPE 1” or
“TAPE 2” position, the sound can be heard immediately
after it is recorded.
Use the tape-monitor selector@, therefore, to confirm that
the source sound is being recorded correctly, by switching
back and forth between the “SOURCE” position and the
“TAPE 1” or ‘‘TAPE 2” positicn.
Tape monitoring (if the tape deck has 3 heads):
To monitor sound recorded by tape deck 1
Record player 1 or 2
8-track stereo tape deck etc.
(playback only)
(i. ye ul FM or AM radio
a & program source
f’ Ba. :
aia
(XY Input selector @
ae
Me, ie FS a7
eee ORF a TH |
@ T=
|
PLAYBACK PLAYBACK
>.
Tape deck 1
Tape deck 2
2)
O SOURCE
—~{) O
TAPE 1%. TAPE 2
a ' DIN (REC/PLAY)
De tees Seer cen ends es Gat om ease terminal
Ho Speaker
Notes: 1. Si1-S2 Recording-mode selector
53 Tape-monitor selector 4)
2. Tape deck 2 sound can be monitored by
setting S3 to ‘TAPE 2” position.