Technics SU-A600 Operating Instructions

Technical Specifications (DIN 45 500)
20 Hz-20 kHz continuous power output
both channels driven [SU-A700]: 2 x 45 W (8 ft)
[SU-A600]: 2 x 40 W (8 ft)
1 kHz continuous power output
both channels driven (THD: 1%)
[SU-A700]: 2x55 W (8 ft)
2x80 W {4 ft)
[SU-A600]: 2 x 50 W {8 ft)
2x70 W (4 ft)
63 Hz-12.5 kHz continuous power output
both channels driven (THD: 0.7%)
[SU-A700]: 2 x 50 W (8 ft)
2x70 W {4 ft)
[SU-A600] : 2x45 W (8 ft)
2x65 W {4 ft)
Total harmonic distortion
rated power at 20 Hz-20 kHz
Intermodulation distortion (50 Hz: 7 kHz=4:1,
rated power
Residual hum and noise
Damping factor
Headphones output level/impedance
Load Impedance
A or B, BI-WIRING
A and B
Input sensitivity/impedance
PHONO MM
TUNER, CD, AUX, TAPE 1, TAPE 2
0.01 % (8 ft )
SMPTE)
0.007% (8 ft)
1 mV
60 (8 ft)
30 (4 ft)
540 mV/47 ft
4 ft—16 ft
8 0—16 ft
2.5 mV/47 kft
150 mV/22 kft
Phono maximum input voltage (1 kHz, RMS)
MM 150 mV (150 mV. IHF ' 66 )
S/N (rated power, 4 ft)
PHONO MM 76 dB (78 dB, IHF ’ 66 )
TUNER, CD, AUX, TAPE 1, TAPE 2 91 d 8 (99 dB. IHF * 66 )
S/N at -26 dB power (4 ft)
PHONO MM 68 dB
TUNER, CD, AUX, TAPE 1, TAPE 2 70 dB
S/N at 50 mW power (4 ft)
PHONO MM 64 dB
TUNER, CD, AUX, TAPE 1, TAPE 2 64 dB
Frequency response
PHONO MM RIAA standard curve ±1 dB
(30 Hz-15 kHz)
TUNER, CD, AUX, TAPE 1, TAPE 2
3 Hz-80 kHz(+0, —3 dB)
+0 dB. -0.3 dB (20 Hz-20 kHz)
Tone controls
BASS 50 Hz,+10 to - 10 dB
TREBLE 20 kHz, +10 to -10 dB
Output voltage
TAPE 1, TAPE 2 REC OUT 150 mV
Channel balance (AUX 250 Hz- 6.3 kHz) ±1 dB
Channel separation (AUX 1 kHz) 50 dB
■ GENERAL
Power consumption 200 W
Power supply
For Europe 50 Hz/60 Hz AC, 230 V
For United Kingdom, Australia and N.Z.
50 HZ/60 Hz AC, 230 V-240 V
For others 50 Hz/60 Hz AC, 110 V -127 V/220 V-240 V
Dimensions (W x H x D) 430x125x318 mm
weight .• [SU-A700]: 8.4 kg
[SU-A600]: 6.2 kg
Notes:
1 . Specifications are subject to change without notice.
Weight and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
For United Kingdom only
This apparatus was produced to BS 800.
Maintenance
To clean this unit, use a soft, dry cloth.
For very dirty surfaces, dip a soft cloth in a weak soap-and-water
solution and wring well. After cleaning, wipe with a soft, dry cloth.
Never use alcohol, paint thinner, benzine, or a chemically treated
cloth to clean this unit.
Such chemicals may damage the unit’s finish.

Technics SU-A600 Specifications

General

Input Sensitivity	2.5mV (MM), 150mV (line)
Speaker Load Impedance	4Ω to 16Ω
Type	Integrated Amplifier
Dimensions	430 x 134 x 315 mm
Damping Factor	60 (8 ohms)