EasyManua.ls Logo

Tecnoware EVO DSP MM 1.3 Rack Tower - User Manual

Tecnoware EVO DSP MM 1.3 Rack Tower
66 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Uninterruptible Power Supply
EVO DSP MM 1.3 Rack Tower
EVO DSP MM 2.6 Rack Tower
EVO DSP MM 4.0 Rack Tower
User’s manual
Manuale utente

Table of Contents

Questions and Answers

  • J
    Julie ReidAug 8, 2025
    What to do if my Tecnoware UPS is beeping twice every second?
    • E
      Erin GreenAug 8, 2025
      If your Tecnoware UPS is beeping twice every second and the icons are flashing on the LCD display, it indicates that the UPS is overloaded. You should remove some of the devices connected to the UPS output to reduce the load. If devices connected to the UPS are fed directly by the mains via the Bypass, you should still remove excessive loads from the UPS output. If the UPS is locked in Bypass mode after repetitive overloads, first remove the excess loads, then shut down the UPS and restart it.
  • K
    Kimberly JonesAug 12, 2025
    Why is the battery backup time shorter than expected on my Tecnoware EVO DSP MM 1.3 Rack Tower?
    • C
      Christopher MorrisAug 13, 2025
      If the battery backup time on your Tecnoware UPS is shorter than expected, it could be due to a couple of reasons. First, the batteries might not be fully charged. In this case, charge the batteries for at least 4 hours and then check the capacity. If the problem persists, the batteries may be defective or faulty.
  • E
    elizabethduncanAug 17, 2025
    What does fault code 14 mean on my Tecnoware EVO DSP MM 1.3 Rack Tower?
    • C
      Crystal MillerAug 17, 2025
      If fault code 14 is displayed on your Tecnoware UPS, accompanied by a lit icon and continuous beeping, it indicates a short circuit on the UPS output. You should check the output wiring and any connected devices for a short circuit.
  • W
    Wyatt WatkinsAug 20, 2025
    Why is my Tecnoware EVO DSP MM 1.3 Rack Tower UPS beeping every second?
    • S
      Susan KellyAug 20, 2025
      If your Tecnoware UPS is beeping every second and the icons are flashing on the graphic display, it could be due to two reasons. First, the line and neutral poles of the AC input line may be reversed. To fix this, disconnect the input cable from the AC input mains socket, rotate the plug by 180°, and then connect it again. Second, the internal batteries might be incorrectly connected. In this case, check if all the batteries are connected correctly.
  • H
    Heather MartinAug 25, 2025
    What does fault code 43 mean on a Tecnoware UPS?
    • J
      Jessica RileyAug 26, 2025
      If your Tecnoware UPS shows fault code 43, the icon lights up on the LCD display, and the alarm beeps continuously, it means the UPS was overloaded for too long and has become faulty, causing it to shut down automatically. To resolve this, remove excess loads from the UPS output and then restart the UPS.
  • A
    Allison HuangAug 29, 2025
    How to fix a Tecnoware EVO DSP MM 1.3 Rack Tower with no display or alarm?
    • C
      Christopher BaileyAug 30, 2025
      If your Tecnoware UPS has no display or alarm even when the main power is normal, it could be due to a couple of reasons. First, the input cable might not be properly connected to the AC input mains or the UPS. Check if the input cable is firmly connected to both. Second, the input circuit breaker might be off. Check the input circuit breaker and, if it's off, push the external button to reactivate it.
  • C
    Christopher EstradaSep 2, 2025
    What does it mean when the EPO function is enabled on Tecnoware UPS?
    • P
      philip00Sep 2, 2025
      If the icon and a warning code flash on the LCD display and the alarm beeps every second on your Tecnoware UPS, it indicates that the EPO (Emergency Power Off) function is enabled. To disable it, set the EPO circuit in a closed position.

Tecnoware EVO DSP MM 1.3 Rack Tower Specifications

General IconGeneral
Power Rating1300 VA
Apparent Power1300 VA
Input Voltage230 VAC
Nominal Input Voltage230 VAC
Output Voltage230 VAC
TechnologyLine Interactive
CategoryUPS
ModelEVO DSP MM 1.3
BrandTecnoware
Battery TypeSealed Lead Acid
Form FactorRack/Tower

Related product manuals