What to do if the Tecnoware UPS is overloaded and beeping?
If your Tecnoware UPS is beeping twice every second and the LCD display icons are flashing, it indicates the UPS is overloaded. The solution is to remove some of the connected devices from the UPS output to reduce the load.
What to do if Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 shows fault code 14 and beeps continuously?
If your Tecnoware UPS displays fault code 14, the icon lights up on the LCD, and an alarm beeps continuously, it means a short circuit has occurred on the UPS output. You should check the output wiring and any connected devices for a short circuit.
What to do if the Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 shows fault code 43 and keeps beeping?
If your Tecnoware UPS displays fault code 43, the icon lights up on the LCD, and the alarm beeps continuously, it means the UPS was overloaded for too long and has become faulty, causing it to shut down automatically. Remove excess loads from the UPS output and then restart it.
Why Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 has no power even if the main is normal?
If there is no indication or alarm on the front panel of your Tecnoware UPS, and the graphic display is off even when the main power is normal, it could be due to a couple of reasons. First, check that the input cable is firmly connected to both the AC input mains and the UPS's AC input socket. Secondly, verify that the input circuit breaker is not in the OFF position. If it is, push the external button to reactivate it.
What does it mean when my Tecnoware UPS beeps every second?
If your Tecnoware UPS is beeping every second and icons are flashing on the graphic display, it indicates that the line and neutral poles of the AC input line are reversed. To fix this, disconnect the input cable from the AC input mains socket, rotate the plug by 180 degrees, and then reconnect it.
Why is the battery backup time shorter than expected on my Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 UPS?
If the battery backup time of your Tecnoware UPS is shorter than the nominal value, it might be because the batteries are not fully charged. Charge the batteries for at least 4 hours and then check their capacity. If the problem persists, consult Technical Service.
What to do if Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 UPS beeps twice every second?
If your Tecnoware UPS is beeping twice every second, it indicates that the UPS is overloaded. Try removing some of the devices connected to the UPS output. If the devices connected to the UPS are fed directly by the mains via the Bypass, remove excessive loads from UPS Output. If the UPS is locked in Bypass mode after repetitive overloads, remove excess loads, then shut down the UPS and restart it.
Why is the Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 UPS battery backup time shorter than expected?
A shorter than expected battery backup time on your Tecnoware UPS can occur if the batteries are not fully charged. Charge the batteries for at least 4 hours and then check capacity. It may also indicate that the batteries are defective or faulty.
How to fix a Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 UPS with no display or alarm?
If your Tecnoware UPS has no display or alarm, first check if the input cable is firmly connected to both the AC input mains and the UPS input socket. Also, check the input circuit breaker; if it's off, push the external button to reactivate it.
What does fault code 14 mean on my Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 UPS?
Fault code 14 on your Tecnoware UPS indicates a short circuit on the UPS output. Check the output wiring and the devices connected to see if any are causing a short circuit.
General| Category | UPS |
|---|---|
| Model | EVO DSP PLUS MM 2.0 - pf 0, 9 |
| Power Factor | 0.9 |
| Power Rating | 2000 VA |
| Output Power | 1800 W |
| Battery Capacity | 9 Ah |
| Output Voltage | 230 V |
| Output Frequency | 50/60 Hz |
| Number of Outlets | 4 |
| Input Voltage | 230 VAC (170-280 VAC) |
To Next Page