To Next Page
T
Trevor LittleAug 15, 2025
What to do if Tecnoware EVO DSP PLUS MM 1.2 is overloaded?
- JjessewhiteAug 15, 2025
If the Tecnoware UPS is overloaded, you should remove some of the connected devices from the UPS output.
What to do if Tecnoware EVO DSP PLUS MM 1.2 is overloaded?
If the Tecnoware UPS is overloaded, you should remove some of the connected devices from the UPS output.
What to do if Tecnoware EVO DSP PLUS MM 1.2 shows fault code 14?
If the Tecnoware UPS displays fault code 14, accompanied by a lit icon and continuous beeping, it indicates a short circuit on the UPS output. Check the output wiring and the connected devices for any short circuit.
How to unlock Tecnoware EVO DSP PLUS MM 1.2 UPS from Bypass mode?
If your Tecnoware UPS is locked in Bypass mode after repetitive overloads, first remove the excess loads from the UPS output. Then, shut down the UPS and restart it.
Why is my Tecnoware UPS beeping twice every second?
If the icons are flashing on the LCD display of your Tecnoware UPS and the alarm beeps twice every second, it means the UPS is overloaded. Remove some of the loads from the UPS output.
What does fault code 43 mean on a Tecnoware UPS?
If fault code 43 is displayed on your Tecnoware UPS, accompanied by a lit icon on the LCD and continuous beeping, it means the UPS was overloaded for too long and has become faulty, causing it to shut down automatically. Remove the excess loads from the UPS output and restart it.
Why Tecnoware EVO DSP PLUS MM 1.2 battery backup time is short?
If your Tecnoware UPS battery backup time is shorter than expected, charge the batteries for at least 4 hours and then check the capacity. If the problem persists, contact Technical Service.
Why Tecnoware UPS has no display?
If there is no indication or alarm on the front panel of your Tecnoware UPS, and the graphic display is off, check the following: * Ensure the input cable is firmly connected to both the AC input mains and the UPS AC input socket. * Check the input circuit breaker. If it is off, push the external button to reactivate it.
What does it mean when Tecnoware UPS displays fault code 1, 2, 3, 4, 11, 12, 13 or 41?
If fault code 1, 2, 3, 4, 11, 12, 13 or 41 is shown on the LCD display of your Tecnoware UPS and the alarm beeps continuously, contact Technical Service, as a UPS internal fault has occurred.
Why is Tecnoware EVO DSP PLUS MM 1.2 beeping and the icon is flashing?
If the icons are flashing on the LCD display and the alarm beeps every second on your Tecnoware UPS, it indicates that the external or internal batteries are incorrectly connected. Check if all batteries are connected correctly.
Describes the UPS operation when input mains power is available and within specifications.
Describes the UPS operation when AC Input power fails, using battery power.
Describes the UPS operation where AC Input is directly connected to outlets via Automatic Bypass.
Provides step-by-step instructions for connecting the UPS to the AC outlet and devices.
Explains how to turn the UPS ON, switch to Stand-by, and turn it completely OFF.
Emphasizes safety when the UPS is not responding correctly or has visible damage.
General| Input Voltage | 230 VAC |
|---|---|
| Battery Voltage | 12 V |
| Waveform | Simulated Sine Wave |
| Input Connection | IEC 320 C14 |
| Capacity | 1200 VA |
| Output Voltage | 230 VAC |
| Topology | Line Interactive |
| Communication Interface | USB |
| Protection | Overload, Short Circuit, Surge, Over Voltage, Deep Discharge |
| Operating Temperature | 0-40°C |
| Frequency | 50/60 Hz |
| Battery Type | Sealed Lead-Acid (SLA) |
