Telguard TG-4 - Page 7

56033504 © 2007 Telular Corporation
vi
4.5 CONNECT SUPERVISORY TRIP OUTPUTS ........................................................................................ 6
4.6 COMPLETE THE INSTALLATION........................................................................................................ 6
5.0 INSTALLATION STEPS..............................................................................................................7
5.1 STEP 1: REGISTER THE TELGUARD UNIT FOR CELLULAR SERVICE .................................................... 7
5.1.1 Register for Cellular Service .................................................................................................... 7
5.2 STEP 2: LOCATE UNIT AND MEASURE SIGNAL STRENGTH (RSSI) ....................................................7
5.2.1 Locate Unit............................................................................................................................... 7
5.2.2 Connect Backup Battery and AC Power Transformer ............................................................. 7
5.2.3 Connect Antenna and Temporarily Place Unit......................................................................... 7
5.2.3.1 Tips for Improved Radio Signal Reception....................................................................................................... 8
5.2.4 Measure Received Signal Strength (RSSI) for Best Antenna Placement ............................... 8
5.2.4.1 Antenna Options.............................................................................................................................................. 8
5.3 STEP 3: TRANSMIT C/C ALARMS OVER THE TELCO CONNECTION ..................................................... 9
5.3.1 Connect C/C to Telguard Jack J7 (BLACK Connector) ........................................................... 9
5.3.2 Connect telco line (RJ-31x Jack) to Telguard Jack J6 (GRAY Connector) ............................. 9
5.3.3 Verify Alarm Signal Transmissions over Telco ........................................................................ 9
5.4 STEP 4: PROGRAM, ACTIVATE & TRANSMIT C/C ALARMS OVER CELLULAR NETWORK ....................... 9
5.4.1 Setup & Programming the Operating Parameters in the Telguard............................................. 10
5.4.1.1 Command Key Sequences for Pots Programming ....................................................................................... 10
5.4.2 Disconnect telco line (RJ-31x Jack) from Telguard Jack J6 (GRAY Connector)................... 11
5.4.3 Verify Alarm Signal Transmissions over Cellular................................................................... 11
5.4.4 Re-connect telco line (RJ-31x Jack) to Telguard Jack J6 (GRAY Connector) ......................12
5.5 STEP 5: CONNECT SUPERVISORY TRIP OUTPUTS.......................................................................... 12
5.5.1 Decide on a STC Trip Output Strategy .................................................................................. 12
5.5.2 Check Telguard Supervisory Trip to C/C ............................................................................... 12
5.5.2.1 Reprogram C/C to Send Proper Code ....................................................................................................... 12
5.5.2.2 Check Proper Operation of Telguard Supervisory Output....................................................................... 12
5.6 STEP 6: COMPLETE THE TELGUARD INSTALLATION ........................................................................ 13
5.6.1 Check Settings....................................................................................................................... 13
5.6.2 Permanently Mount and Properly Ground the Telguard Chassis .......................................... 13
A1.0 APPENDICES..................................................................................................................................... 14
A1.1 WIRING DIAGRAM ........................................................................................................................ 14
A1.2 JACK AND PIN ASSIGNMENTS .......................................................................................................15
A1.3 TERMINAL STRIP PIN ASSIGNMENTS ............................................................................................. 15
A1.4 LED MODES AND FUNCTIONS ...................................................................................................... 16
A2.0 OPERATIONAL QUICK REFERENCE TABLE ........................................................................ 17
A2.1 ACTIVATION FORM ................................................................................................................. 18
A2.2 COMPATIBLE CONTROL COMMUNICATORS ....................................................................................19
A3.0 DETAILED SPECIFICATIONS ..........................................................................................................19
A3.1 DIALER TO INTERFACE ELECTRONICS ...........................................................................................19
A3.2 POWER .......................................................................................................................................19
A3.3 DIGITAL CELLULAR RADIO ............................................................................................................ 19
A3.4 TELCO INTERFACE ....................................................................................................................... 19
A4.0 PARTS LIST..............................................................................................................................20