Need help?Do you have a question about the Tescom DS3100 and is the answer not in the manual?
General safety instructions for UPS operation and handling.
Specific warnings about electrical hazards, ventilation, and battery safety.
Features PWM, IGBT, DSP control, and true on-line topology.
Pure sinusoidal output, overload, over-current, short circuit protection.
Includes cold-start, static bypass, maintenance bypass, and unbalanced load operation.
LCD panel, event logging, PC diagnostics, and improved fault information.
Explanation of Rectifier, Battery, and Inverter module functions and technologies.
UPS response during mains failure using battery power.
UPS behavior when the load is transferred to the bypass source.
Identification of connection terminals for power and communication.
Detailed specifications for output ratings and input power.
Output voltage/frequency, battery configuration, and interface details.
Critical safety warnings and step-by-step unpacking instructions.
Recommendations for selecting a suitable installation location for the UPS.
Guidelines for power line, grounding, and recommended cable sizes/fuses.
Emphasizing proper earthing procedures to prevent hazards.
Step-by-step instructions for connecting the UPS power cables.
Accessing and clearing recorded alarm events and messages.
Commands to transfer load to bypass, start tests, and initialize modem.
List of fault codes and descriptions for the rectifier module.
Codes detailing inverter output phase voltage and current status.
Troubleshooting for rectifier faults and input voltage issues.
Diagnosing line failures, DC bus voltage problems, and frequency tolerance.
Troubleshooting output overcurrent, overtemperature, and overload shutdowns.
Troubleshooting bypass failures, battery low, and battery shutdown.
Step-by-step procedures for starting and safely shutting down the UPS.
Instructions for switching the UPS from normal operation to maintenance bypass.
Steps to switch the UPS back from maintenance bypass to normal operation.
Describes UPS operation during power outages and battery autonomy time.
Explanation of 'BATTERY LOW' and 'BATTERY LOW SHUT' messages.
Warning against opening the UPS; user-serviceable parts disclaimer.
Systematic approach to identifying and diagnosing faults.
Steps to check before calling technical service for assistance.
General safety instructions for UPS operation and handling.
Specific warnings about electrical hazards, ventilation, and battery safety.
Features PWM, IGBT, DSP control, and true on-line topology.
Pure sinusoidal output, overload, over-current, short circuit protection.
Includes cold-start, static bypass, maintenance bypass, and unbalanced load operation.
LCD panel, event logging, PC diagnostics, and improved fault information.
Explanation of Rectifier, Battery, and Inverter module functions and technologies.
UPS response during mains failure using battery power.
UPS behavior when the load is transferred to the bypass source.
Identification of connection terminals for power and communication.
Detailed specifications for output ratings and input power.
Output voltage/frequency, battery configuration, and interface details.
Critical safety warnings and step-by-step unpacking instructions.
Recommendations for selecting a suitable installation location for the UPS.
Guidelines for power line, grounding, and recommended cable sizes/fuses.
Emphasizing proper earthing procedures to prevent hazards.
Step-by-step instructions for connecting the UPS power cables.
Accessing and clearing recorded alarm events and messages.
Commands to transfer load to bypass, start tests, and initialize modem.
List of fault codes and descriptions for the rectifier module.
Codes detailing inverter output phase voltage and current status.
Troubleshooting for rectifier faults and input voltage issues.
Diagnosing line failures, DC bus voltage problems, and frequency tolerance.
Troubleshooting output overcurrent, overtemperature, and overload shutdowns.
Troubleshooting bypass failures, battery low, and battery shutdown.
Step-by-step procedures for starting and safely shutting down the UPS.
Instructions for switching the UPS from normal operation to maintenance bypass.
Steps to switch the UPS back from maintenance bypass to normal operation.
Describes UPS operation during power outages and battery autonomy time.
Explanation of 'BATTERY LOW' and 'BATTERY LOW SHUT' messages.
Warning against opening the UPS; user-serviceable parts disclaimer.
Systematic approach to identifying and diagnosing faults.
Steps to check before calling technical service for assistance.
General| Waveform | Sine wave |
|---|---|
| Frequency | 50/60Hz |
| Communication Interface | RS-232, USB |
| Operating Temperature | 0-40 °C |
| Storage Temperature | -15°C to 45°C (5°F to 113°F) |
| Humidity | 0% to 95% non-condensing |
To Next Page
