Need help?Do you have a question about the THORENS TD 102 A and is the answer not in the manual?
Thanks for choosing THORENS. Read this manual for optimal performance.
Avoid dust cover items; heat, vibration, dust, cold, moisture. Ensure ventilation. Do not move during playback.
Wipe dust with a soft cloth dampened with diluted neutral cleaner.
Place on a flat, level surface. Place rubber mat on turntable platter.
Connect audio equipment via analog output. PHONO EQ switch adjusts signal type. Caution: High output with PHONO input.
Connect the included AC adapter. Use only provided adapter. Press STANDBY/ON to operate.
Insert hinges to attach. Lift cover with hinges to remove.
Hold front edge to open. Lower gently to close.
Identifies Platter, Counterweight, Tonearm lifter, Tonearm holder, Tonearm, and Headshell.
Details START button, Record size selection, STOP button, and 33/44 RPM switch.
Bent styluses damage records and cause malfunctions. Handle styluses with care.
Use only commercially available stylus cleaners. Other substances can damage the stylus.
Stylus damage from user error or external factors is not covered by warranty.
Avoid touching grooves. Clean records with designated cleaner, not thinner.
Avoid heat, humidity, direct sun. Do not stack or store at an angle. Store in sleeves. Do not use cracked records.
Screw counterweight, release tonearm, allow it to float freely, then balance the arm.
Set scale to '0' without moving counterweight. Adjust to '2' grams for the specified cartridge.
Remove stylus cap. Turn on unit. Open dust cover. Place record. Select size/speed. Press START. Playback cannot be stopped mid-operation.
Do not touch tonearm/record. Do not forcibly stop platter rotation. Reduce volume if feedback occurs.
Automatic stop at lead-out groove. Press STOP to pause/stop mid-play. Start mid-track by positioning tonearm.
Details drive system, motor type, rotational speeds, speed variation, wow/flutter, and signal-to-noise ratio.
Specifies platter diameter, tonearm length, tracking force, and overhang.
Details cartridge type, output voltage, tracking force, and cartridge weight.
Specifies power input voltage, frequency, and power consumption at standby.
Provides overall dimensions (W x D x H) and weight including the dust cover.
Specifies maximum operating temperature and altitude/climate safety labels.
Thanks for choosing THORENS. Read this manual for optimal performance.
Avoid dust cover items; heat, vibration, dust, cold, moisture. Ensure ventilation. Do not move during playback.
Wipe dust with a soft cloth dampened with diluted neutral cleaner.
Place on a flat, level surface. Place rubber mat on turntable platter.
Connect audio equipment via analog output. PHONO EQ switch adjusts signal type. Caution: High output with PHONO input.
Connect the included AC adapter. Use only provided adapter. Press STANDBY/ON to operate.
Insert hinges to attach. Lift cover with hinges to remove.
Hold front edge to open. Lower gently to close.
Identifies Platter, Counterweight, Tonearm lifter, Tonearm holder, Tonearm, and Headshell.
Details START button, Record size selection, STOP button, and 33/44 RPM switch.
Bent styluses damage records and cause malfunctions. Handle styluses with care.
Use only commercially available stylus cleaners. Other substances can damage the stylus.
Stylus damage from user error or external factors is not covered by warranty.
Avoid touching grooves. Clean records with designated cleaner, not thinner.
Avoid heat, humidity, direct sun. Do not stack or store at an angle. Store in sleeves. Do not use cracked records.
Screw counterweight, release tonearm, allow it to float freely, then balance the arm.
Set scale to '0' without moving counterweight. Adjust to '2' grams for the specified cartridge.
Remove stylus cap. Turn on unit. Open dust cover. Place record. Select size/speed. Press START. Playback cannot be stopped mid-operation.
Do not touch tonearm/record. Do not forcibly stop platter rotation. Reduce volume if feedback occurs.
Automatic stop at lead-out groove. Press STOP to pause/stop mid-play. Start mid-track by positioning tonearm.
Details drive system, motor type, rotational speeds, speed variation, wow/flutter, and signal-to-noise ratio.
Specifies platter diameter, tonearm length, tracking force, and overhang.
Details cartridge type, output voltage, tracking force, and cartridge weight.
Specifies power input voltage, frequency, and power consumption at standby.
Provides overall dimensions (W x D x H) and weight including the dust cover.
Specifies maximum operating temperature and altitude/climate safety labels.
General| Speed | 33-1/3, 45 RPM |
|---|---|
| Platter | 300 mm Aluminium, die-cast, non-magnetic |
| Tonearm | THORENS TP 72 |
| Cartridge | Audio Technica AT-VM95E |
| Dimensions | 420 x 355 x 121 mm |
| Weight | 5.7 kg |
| Motor | Electronically controlled DC motor |
| Outputs | RCA line output |
| Type | Automatic Turntable |
| Power Supply | External power supply, 12V DC, 1.5A |
To Next Page
