Titan LX-65 User Manual

English
© Titan Tool Inc. All rights reserved. 1
Instruction Sheet
LX-65
High Capacity Spray Gun
Important Safety Instructions
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
 a) SAVETHESEINSTRUCTIONS–Toreducetherisksofreor
explosion, electrical shock, and the injury to persons, read and
understand all instructions included in this manual. Be familiar
with the controls and the proper usage of the equipment.
 b) WARNING-Toreducetheriskofreor
explosion:
 1. Donotsprayammableorcombustiblematerials
nearanopename,pilotlightsorsourcesofignitionsuchashot
objects,cigarettes,motors,electricalequipmentandelectrical
appliances.Avoidcreatingsparksfromconnectinganddisconnecting
powercords.
 2. Useextremecautionwhenusingmaterialswithaashpointbelow
70ºF(21ºC).Flashpointisthetemperaturethatauidcanproduce
enoughvaporstoignite.
 3. Paintorsolventowingthroughtheequipmentisabletoresultin
staticelectricity.Staticelectricitycreatesariskofreorexplosionin
thepresenceofpaintorsolventfumes.Allpartsofthespraysystem,
includingthepump,hoseassembly,spraygunandobjectsinand
aroundthesprayareashallbeproperlygroundedtoprotectagainst
staticdischargeandsparks.Useonlyconductiveorgroundedhigh-
pressureairlesspaintsprayerhosesspeciedbythemanufacturer.
 4. Verifythatallcontainersandcollectionsystemsaregroundedto
preventstaticdischarge.
 5. Connecttoagroundedoutletandusegroundedextensioncords
(electricmodelsonly).Donotusea3to2adapter.
 6. Donotuseapaintorsolventcontaininghalogenatedhydrocarbons.
Suchaschlorine,bleachmildewcide,methylenechlorideand
trichloroethane.Theyarenotcompatiblewithaluminum.Contactthe
coatingsupplieraboutcompatibilityofmaterialwithaluminum.
 7. Keepsprayareawellventilated.Keepagoodsupplyoffreshair
movingthroughtheareatokeeptheairwithinthesprayareafree
fromaccumulationofammablevapors.Keeppumpassemblyinwell
ventilatedarea.Donotspraypumpassembly.
 8. Donotsmokeinthesprayarea.
 9. Donotoperatelightswitches,engines,orsimilarsparkproducing
productsinthesprayarea.
 10. Keepareacleanandfreeofpaintorsolventcontainers,rags,and
otherammablematerials.
 11. Knowthecontentsofthepaintandsolventsbeingsprayed.Read
allMaterialSafetyDataSheets(MSDS)andcontainerlabels
providedwiththepaintsandsolvents.Followthepaintandsolvent
manufacture’ssafetyinstructions.
 12. Placepumpatleast25feet(7.62meters)fromthesprayobjectina
wellventilatedarea(addmorehoseifnecessary).Flammablevapors
areoftenheavierthanair.Floorareamustbeextremelywellventilated.
Thepumpcontainsarcingpartsthatemitsparksandcanignitevapors.
 13. Plasticcancausestaticsparks.Neverhangplastictoenclosespray
area.Donotuseplasticdropclothswhensprayingammable
material.
 14. Fireextinguisherequipmentshallbepresentandworking.
c) WARNING - To reduce the risk of skin injection:
 1. Donotaimthegunat,orsprayanypersonoranimal.
 2. Keephandsandotherbodypartsawayfromthedischarge.
Forexample,donottrytostopleakswithanypartofthebody.
 3. Alwaysusethenozzletipguard.Donotspraywithoutthenozzletip
guardinplace.
 4. Onlyuseanozzletipspeciedbythemanufacturer.
 5. Usecautionwhencleaningandchangingnozzletips.Inthecase
wherethenozzletipclogswhilespraying,ALWAYSlockguntrigger,
shutpumpoff,andreleaseallpressurebeforeservicing,cleaningtip
orguard,orchangingtip.Pressurewillnotbereleasedbyturningoff
themotor.ThePRIME/SPRAYvalveorpressurebleedvalvemustbe
turnedtotheirappropriatepositionstorelievesystempressure.Refer
toPRESSURERELIEFPROCEDUREdescribedinthepumpmanual.
 6. Donotleavetheunitenergizedorunderpressurewhileunattended.
Whentheunitisnotinuse,turnofftheunitandrelievethepressurein
accordancewiththemanufacturer’sinstructions.
 7. High-pressuresprayisabletoinjecttoxinsintothebodyandcause
seriousbodilyinjury.Intheeventthatinjectionoccurs,seekmedical
attentionimmediately.
 8. Checkhosesandpartsforsignsofdamage,aleakcaninjectmaterial
intotheskin.Inspecthosebeforeeachuse.Replaceanydamaged
hosesorparts.
 9. Thissystemiscapableofproducing3600PSI/248Bar.Only
usereplacementpartsoraccessoriesthatarespeciedbythe
manufacturerandthatareratedaminimumof3600PSI.Thisincludes
spraytips,nozzleguards,guns,extensions,ttings,andhose.
 10. Alwaysengagethetriggerlockwhennotspraying.Verifythetrigger
lockisfunctioningproperly.
 11. Verifythatallconnectionsaresecurebeforeoperatingtheunit.
 12. Knowhowtostoptheunitandbleedpressurequickly.Bethoroughly
familiarwiththecontrols.Pressurewillnotbereleasedbyturningoff
themotor.ThePRIME/SPRAYvalveorpressurebleedvalvemustbe
turnedtotheirappropriatepositionstorelievesystempressure.Refer
toPRESSURERELIEFPROCEDUREdescribedinthepumpmanual.
 13. Alwaysremovethespraytipbeforeushingorcleaningthesystem.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury. It is important to
treat the injury as soon as possible. DO NOT delay treatment
to research toxicity. Toxicity is a concern with some coatings
injected directly into the blood stream. Consultation with a plastic
surgeon or reconstructive hand surgeon may be advisable.
d) WARNING - To reduce the risk of injury:
 1. Alwayswearappropriategloves,eyeprotection,clothinganda
respiratorormaskwhenpainting.Hazardousvapors–Paints,
solvents,insecticides,andothermaterialscanbeharmfulifinhaledor
comeincontactwithbody.Vaporscancauseseverenausea,fainting
orpoisoning.
 2. Donotoperateorspraynearchildren.Keepchildrenawayfrom
equipmentatalltimes.
 3. Donotoverreachorstandonanunstablesupport.Keepeffective
footingandbalanceatalltimes.
 4. Stayalertandwatchwhatyouaredoing.
 5. Donotoperatetheunitwhenfatiguedorundertheinuenceofdrugs
oralcohol.
 6. Donotkinkorover-bendthehose.Airlesshosecandevelopleaks
fromwear,kinkingandabuse.Aleakcaninjectmaterialintotheskin.
 7. Donotexposethehosetotemperaturesorpressuresinexcessof
thosespeciedbymanufacturer.
 8. Donotusethehoseasastrengthmembertopullorlifttheequipment.
 9. Uselowestpossiblepressuretoushequipment.
 10. Followallappropriatelocal,stateandnationalcodesgoverning
ventilation,repreventionandoperation.
 11. TheUnitedStatesGovernmentSafetyStandardshavebeenadopted
undertheOccupationalSafetyandHealthAct(OSHA).These
standards,particularlypart1910oftheGeneralStandardsandpart
1926oftheConstructionStandardsshouldbeconsulted.
 12. Beforeeachuse,checkallhosesforcuts,leaks,abrasionorbulging
ofcover.Checkfordamageormovementofcouplings.Immediately
replacehoseifanyofthoseconditionsexist.Neverrepairapainthose.
Replacewithaconductivehigh-pressurehose.
 13. Donotsprayoutdoorsonwindydays.
 14. Alwaysunplugcordfromoutletbeforeworkingonequipment(electric
modelsonly).
0811 • Form No. 0286751C

Titan LX-65 Specifications

General

Flow Rate	0.31 GPM
Horsepower	0.6 HP
Power Source	Electric
Voltage	120 V
Type	Airless

Summary

Important Safety Instructions

Save These Instructions

Instructions for safe operation and understanding controls.

Fire and Explosion Prevention

Precautions to prevent fire and explosion hazards during operation.

Skin Injection Hazards

Warnings and procedures to prevent serious bodily injury from high-pressure injection.

Physician Guidance

Guidance for medical professionals treating injection injuries.

General Injury Prevention

General safety guidelines to prevent injury during equipment use.

Using the Gun Trigger Lock

Locking and Unlocking the Trigger

Instructions on how to engage and disengage the trigger lock mechanism.

Changing a Tip

Tip Removal and Replacement

Steps for safely removing and installing spray tips and guards.

Identifying Tip Sizes

Explains how to interpret spray tip size designations for pattern and orifice.

Cleanup

General Cleanup Procedures

Guidance on maintaining the gun after use to ensure proper operation.

Flammable Solvent Cleanup

Special safety instructions when cleaning with flammable materials.

Maintenance

Replacing/Servicing the Seal Assembly

Steps for replacing the seal assembly to fix leaks or spitting.

Adjusting the Seal Assembly

Procedures for proper seal assembly adjustment for positive shut-off.

Replacing/Removing the Filter

Instructions for filter replacement and maintenance.

Gun Filter Chart

Parts List

Warranty