Titan LX-75 - User Manual

Important Safety Instructions
Read all safety information before operating the
equipment. Save these instructions.
Indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To reduce the risks of re or explosion, electrical shock and the
injury to persons, read and understand all instructions included in
this manual. Be familiar with the controls and proper usage of the
equipment.
WARNING: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Property damage and/
or severe injury can occur.
PREVENTION:
 • Donotsprayammableorcombustiblematerialsnearanopename,
pilotlightsorsourcesofignitionsuchashotobjects,cigarettes,motors,
electrical equipment and electrical appliances. Avoid creating sparks from
connecting and disconnecting power cords.
 • Forunitsintendedforusewithonlywater-basedormineralspirit-type
materialswithaminimumashpointof38ºC(100ºF)—Donotsprayor
cleanwithliquidshavingaashpointoflessthan38ºC(100ºF).Flashpoint
isthetemperatureatwhichauidcanproduceenoughvaportoignite.
 • Useextremecautionwhenusingmaterialswithaashpointbelow100ºF
(38ºC).Refer to your pump manual to determine if these materials can
be sprayed.
 • Paintorsolventowingthroughtheequipmentisabletoresultinstatic
electricity. Static electricity creates a risk of re or explosion in the presence
ofpaintorsolventfumes.Allpartsofthespraysystem,includingthe
pump,hoseassembly,spraygunandobjectsinandaroundthesprayarea
shallbeproperlygroundedtoprotectagainststaticdischargeandsparks.
Useonlyconductiveorgroundedhigh-pressureairlesspaintsprayerhoses
speciedbythemanufacturer.
 • Verifythatallcontainersandcollectionsystemsaregroundedtoprevent
static discharge.
 • Connecttoagroundedoutletandusegroundedextensioncords(electric
modelsonly).Donotusea3to2adapter.
 • Donotuseapaintorsolventcontaininghalogenatedhydrocarbons.Such
aschlorine,bleachmildewcide,methylenechlorideandtrichloroethane.
Theyarenotcompatiblewithaluminum.Contactthecoatingsupplier
aboutcompatibilityofmaterialwithaluminum.
 • Keepsprayareawellventilated.Keepagoodsupplyoffreshair
moving through the area to keep the air within the spray area free from
accumulationofammablevapors.Keeppumpassemblyinwellventilated
area.Donotspraypumpassembly.
 • Donotsmokeinthesprayarea.
 • Donotoperatelightswitches,engines,orsimilarsparkproducingproducts
in the spray area.
 • Keepareacleanandfreeofpaintorsolventcontainers,rags,andother
ammablematerials.
 • Knowthecontentsofthepaintandsolventsbeingsprayed.Readall
materialSafetyDataSheets(SDS)andcontainerlabelsprovidedwiththe
paintsandsolvents.Followthepaintandsolventmanufacture’ssafety
instructions.
 • Placepumpatleast25feet(7.62meters)fromthesprayobjectinawell
ventilatedarea(addmorehoseifnecessary).Flammablevaporsareoften
heavierthanair.Floorareamustbeextremelywellventilated.Thepump
contains arcing parts that emit sparks and can ignite vapors.
 • Plasticcancausestaticsparks.Neverhangplastictoenclosesprayarea.Do
notuseplasticdropclothswhensprayingammablematerial.
 • Fireextinguisherequipmentshallbepresentandworking.
WARNING: INJECTION INJURY
Ahighpressurepaintstreamproducedbythisequipmentcanpierce
theskinandunderlyingtissues,leadingtoseriousinjuryandpossible
amputation. See a physician immediately.
PREVENTION:
 • Donotaimthegunat,orsprayanypersonoranimal.
 • Keephandsandotherbodypartsawayfromthedischarge.Forexample,do
nottrytostopleakswithanypartofthebody.
 • NEVERputyourhandinfrontofthegun.Gloveswillnotprovideprotection
against an injection injury.
 • ALWAYSkeepthetipguardinplacewhilespraying.Thetipguardprovides
someprotectionbutismainlyawarningdevice.
 • Onlyuseanozzletipspeciedbythemanufacturer.
 • Usecautionwhencleaningandchangingnozzletips.Inthecasewherethe
nozzletipclogswhilespraying,ALWAYSlockguntrigger,shutpumpo,
andreleaseallpressurebeforeservicing,cleaningtiporguard,orchanging
tip.Pressurewillnotbereleasedbyturningothemotor.ThePRIME/
SPRAYvalveorpressurebleedvalvemustbeturnedtotheirappropriate
positionstorelievesystempressure.RefertoPRESSURERELIEFPROCEDURE
describedinthepumpmanual.
 • Donotleavetheunitenergizedorunderpressurewhileunattended.
Whentheunitisnotinuse,turnotheunitandrelievethepressurein
accordancewiththemanufacturer’sinstructions.
 • High-pressuresprayisabletoinjecttoxinsintothebodyandcauseserious
bodilyinjury.Intheeventthatinjectionoccurs,seekmedicalattention
immediately.
 • Checkhosesandpartsforsignsofdamage,aleakcaninjectmaterialinto
theskin.Inspecthosebeforeeachuse.Replaceanydamagedhosesor
parts.OnlyuseTITANoriginal-high-pressurehosesinordertoensure
functionality,safetyanddurability.
 • Thissystemiscapableofproducing3600PSI/248Bar.Onlyuse
replacementpartsoraccessoriesthatarespeciedbythemanufacturer
andthatareratedaminimumof3600PSI.Thisincludesspraytips,nozzle
guards,guns,extensions,ttings,andhose.
 • Alwaysengagethetriggerlockwhennotspraying.Verifythetriggerlockis
functioning properly.
 • Verifythatallconnectionsaresecurebeforeoperatingtheunit.
 • Knowhowtostoptheunitandbleedpressurequickly.Bethoroughly
familiarwiththecontrols.Pressurewillnotbereleasedbyturningothe
motor.ThePRIME/SPRAYvalveorpressurebleedvalvemustbeturnedto
theirappropriatepositionstorelievesystempressure.RefertoPRESSURE
RELIEFPROCEDUREdescribedinthepumpmanual.
 • Alwaysremovethespraytipbeforeushingorcleaningthesystem.
NOTE TO PHYSICIAN: Injection into the skin is a traumatic injury which can
lead to possible amputation. It is important to treat the injury as soon as
possible. DO NOT delay treatment to research toxicity. Toxicity is a concern
with some coatings injected directly into the blood stream. Consultation
with a plastic surgeon or reconstructive hand surgeon may be advisable.
WARNING: GENERAL
Cancausesevereinjuryorpropertydamage.
PREVENTION:
 • Alwayswearappropriategloves,eyeprotection,clothingandarespiratoror
mask when painting.
 • Donotoperateorspraynearchildren.Keepchildrenawayfromequipment
at all times.
 • Donotoverreachorstandonanunstablesupport.Keepeectivefooting
andbalanceatalltimes.
 • Stayalertandwatchwhatyouaredoing.
 • Donotoperatetheunitwhenfatiguedorundertheinuenceofdrugsor
alcohol.
 • Donotkinkorover-bendthehose.Airlesshosecandevelopleaksfrom
wear,kinkingandabuse.Aleakcaninjectmaterialintotheskin.
 • Donotexposethehosetotemperaturesorpressuresinexcessofthose
speciedbymanufacturer.
 • Donotusethehoseasastrengthmembertopullorlifttheequipment.
 • Uselowestpossiblepressuretoushequipment.
 • Followallappropriatelocal,stateandnationalcodesgoverningventilation,
re prevention and operation.
 • TheUnitedStatesGovernmentSafetyStandardshavebeenadopted
undertheOccupationalSafetyandHealthAct(OSHA).Thesestandards,
particularlypart1910oftheGeneralStandardsandpart1926ofthe
ConstructionStandardsshouldbeconsulted.
 • Beforeeachuse,checkallhosesforcuts,leaks,abrasionorbulgingofcover.
Checkfordamageormovementofcouplings.Immediatelyreplacehose
ifanyofthoseconditionsexist.Neverrepairapainthose.Replacewitha
conductivehigh-pressurehose.
 • Donotsprayoutdoorsonwindydays.
 • Alwaysunplugcordfromoutletbeforeworkingonequipment(electric
modelsonly).
for professional use only • instruction sheet
LX-75 ProfessionaL airLess gun
4’ gun 550-495
8’ gun 550-500
0318 • Form No. 313-2684E

Summary

Important Safety Instructions

Explosion and Fire Safety

Mitigate risks from flammable materials and static electricity during spraying operations.

Injection Injury Prevention

Avoid serious injury from high-pressure paint streams piercing skin.

General Operational Safety

Essential safety measures including protective gear, ventilation, and operator awareness.

Physician Injection Injury Guidance

Critical information for medical professionals treating injection injuries.

Airless Gun Setup Guide

Tip Seal and Retainer Removal

Instructions for removing the tip seal and retainer from the spray gun.

Cleanup and Flushing Procedures

Guidelines for proper gun and system cleanup after use, especially with solvents.

Airless Gun Operation

Spray Tip Changing

Steps for safely removing and installing spray tips without disassembling the gun.

Maintenance: Seal Assembly Replacement

Maintenance: Ball Holder and Diffuser

Maintenance: Filter Replacement

Airless Gun Parts List

Titan Airless Gun Warranty

Titan LX-75 Specifications

General

Brand	Titan
Model	LX-75
Category	Paint Sprayer
Language	English