Toro 20016 User Manual

Footnotes
Not illustrated
n
Not serviced separately
o
Included in Repair Kit No. 632809
p
Obtain from your local Tecumseh dealer
q
Part Description Abbreviations
Part descriptions in this catalog may include the following abbreviations.
AR. . . . . . . . . . . . . . .as required
ASM. . . . . . . . . . . . . assembly
BBC. . . . . . . . . . . . . blade brake clutch
CARR. . . . . . . . . . . . carriage
DEG. . . . . . . . . . . . . degrees
EXT. . . . . . . . . . . . . .external
FH. . . . . . . . . . . . . . . flat head
GA. . . . . . . . . . . . . . .gauge
HF. . . . . . . . . . . . . . . hex flange
HH. . . . . . . . . . . . . . .hex head
HHF. . . . . . . . . . . . . hex head flange
HHFTF. . . . . . . . . . . hex head flange thread forming
HJ. . . . . . . . . . . . . . . hex jam
HLH. . . . . . . . . . . . . .hex lag head
HOC. . . . . . . . . . . . . height-of-cut
HSBH. . . . . . . . . . . . hex socket button head
HSFH. . . . . . . . . . . . hex socket flat head
HSH. . . . . . . . . . . . . hex socket head
HWH. . . . . . . . . . . . . hex washer head
HWHTF. . . . . . . . . . . hex washer head thread
forming
HYD. . . . . . . . . . . . . hydraulic
INC. . . . . . . . . . . . . . incorporated
LH. . . . . . . . . . . . . . . left hand
NI. . . . . . . . . . . . . . . nylon insert
NPTF. . . . . . . . . . . . national pipe thread fine
PFH. . . . . . . . . . . . . .phillips flat head
PPH. . . . . . . . . . . . . phillips pan head
PPHTF. . . . . . . . . . . phillips pan head thread
forming
PRH. . . . . . . . . . . . . phillips round head
PTH. . . . . . . . . . . . . .phillips truss head
PTO. . . . . . . . . . . . . power-take-off
RH. . . . . . . . . . . . . . .right hand
ROPS. . . . . . . . . . . . roll-over-protection-system
SFH. . . . . . . . . . . . . .slotted fillister head
SHH. . . . . . . . . . . . . slotted hex head
SHWH. . . . . . . . . . . . slotted hex washer head
SPH. . . . . . . . . . . . . slotted pan head
SQH. . . . . . . . . . . . . square head
SRH. . . . . . . . . . . . . slotted round head
STD. . . . . . . . . . . . . .standard
TAP. . . . . . . . . . . . . .self tapping
TTH. . . . . . . . . . . . . .torx truss head
Contents
Description Page
. . . . . . 3Deck, Side Chute and Rear Door Assembly
. . . . . . 4Rear Axle Assembly
. . . . . . 5Front Axle and Transmission Assembly
. . . . . . 6Transmission Assembly No. 106-3955
. . . . . . 7Engine and Blade Assembly
. . . . . . 8Bail and Handle Assembly
. . . . . . 9Rear Bag Assembly
Description Page
. . . . . . 10
Engine Assembly Tecumseh Lv195ea-
362003b
. . . . . . 12
Engine Assembly Tecumseh Lv195ea-
362003b (continued)
. . . . . . 14
Carburetor Assembly No. 640303 Tecumseh
Lv195ea-362003b
. . . . . . 15
Recoil Starter Assembly No. 590739
Tecumseh No. Lv195ea-362003b
. . . . . . 16
Recoil Starter Assembly No. 590702
(Optional) Tecumseh Lv195ea-362003b

Toro 20016 Specifications

General

Engine	Briggs & Stratton
Deck Material	Steel
Mulching Capability	Yes
Bagging Capability	Yes
Side Discharge	Yes
Engine Type	4-Cycle
Cutting Width	22 inches
Cutting Height	1 - 4 in (2.5 - 10 cm)
Power Source	Gas
Wheel Size	7 in (front)