Toro 30635 - Locating the Tie-Down Points

76 pages

To Next Page

To Previous Page

LocatingtheTie-Down

Points

Therearetiedownslocatedatthefrontandrearsides

ofthemachine(Figure40).

Note:Useproperly-ratedDOT-approvedstrapsin4

cornerstotiedownthemachine.

•2onthefrontoftheoperator'splatform

•Rearbumper

g196910

Figure40

1.Reartie-downpoint2.Fronttie-downpoints

Main Page

Table of Contents3
Safety4
General Safety4
Safety and Instructional Decals5
Setup15
Greasing the Machine15
Checking the Tire Pressure15
Checking the Fluid Levels15
Installing the Decal16
Only)16
Product Overview17
Controls17
Cab Controls19
Specifications20
Attachments/Accessories21
Before Operation21
Before Operation Safety21
Checking the Engine-Oil Level22
Checking the Cooling System22
Checking the Hydraulic System22
Filling the Fuel Tank22
Checking the Tire Pressure23
Checking the Torque of the Wheel Lug Nuts23
Checking the Planetary-Gear-Drive Oil24
Checking the Rear-Axle Lubricant24
Checking the Rear-Axle-Gearbox Lubricant24
Adjusting the Roll Bar25
Adjusting the Height of Cut25
Adjusting the Skids28
Adjusting the Cutting Unit Rollers29
Correcting a Mismatch between the Cutting Units29
Checking the Safety-Interlock Switches31
Adjusting the Mirrors31
Aiming the Headlights31
Activating the Quiet Mode31
Selecting a Blade32
Using the Infocenter Control32
Using the Menus34
Protected Menus35
Accessing Protected Menus35
Setting the Auto Idle36
Setting the Maximum Allowed Mow Speed36
Setting the Maximum Allowed Transport Speed36
Setting the Service Due Timer36
During Operation36
General Safety36
Rollover Protection System (ROPS) Safety37
Additional ROPS Safety for Machines with a Cab or a Fixed Roll Bar37
Additional ROPS Safety for Machines with a Foldable Roll Bar37
Slope Safety37
Understanding the Operating Characteristics of the Machine38
Operating the Machine38
Understanding Counterbalance39
Using the Brake Pedals39
Understanding Toro Smart Power39
Performing a Fan-Reverse Operation39
Understanding Auto Idle39
Starting the Engine39
Using Cruise Control40
Shutting off the Engine40
Using the Engine-Speed Switch40
Adjusting the Mowing Speed40
Adjusting the Transport Speed40
Operating Tips41
After Operation41
General Safety41
Pushing or Towing the Machine42
Locating the Jacking Points42
Hauling the Machine42
Locating the Tie-Down Points43
Maintenance44
Maintenance Safety44
Recommended Maintenance Schedule(S)44
Daily Maintenance Checklist46
Pre-Maintenance Procedures47
Removing the Hood47
Lubrication47
Greasing the Bearings and Bushings47
Engine Maintenance50
Engine Safety50
Servicing the Engine Oil50
Servicing the Air Cleaner51
Fuel System Maintenance53
Servicing the Fuel System53
Servicing the Water Separator53
Servicing the Fuel Filter54
Electrical System Maintenance54
Electrical System Safety54
Servicing the Battery54
Locating the Fuses55
Drive System Maintenance56
Adjusting the Traction-Pedal Angle56
Changing the Planetary-Gear-Drive Oil56
Changing the Rear-Axle Oil57
Checking the Rear Wheel Toe-In58
Cooling System Maintenance58
Cooling System Safety58
Checking the Cooling System58
Servicing the Engine-Cooling System59
Brake Maintenance60
Adjusting the Service Brakes60
Belt Maintenance60
Servicing the Alternator Belt60
Servicing the Compressor Belt60
Tensioning the Blade-Drive Belts61
Replacing the Blade-Drive Belt61
Hydraulic System Maintenance62
Hydraulic System Safety62
Servicing the Hydraulic System62
Cutting Unit Maintenance65
Pivoting (Tilting) the Front Cutting Unit to the Upright Position65
Pivoting the Front Cutting Unit down66
Adjusting the Cutting Unit Pitch66
Servicing the Caster-Arm Bushings67
Servicing the Caster Wheels and Bearings67
Blade Maintenance68
Blade Safety68
Checking for a Bent Blade68
Removing and Installing the Cutting-Unit Blade(S)69
Inspecting and Sharpening the Cutting Unit Blade(S)69
Correcting a Cutting Unit Mismatch70
Cab Maintenance71
Cleaning the Cab71
Cleaning the Cab Air Filters71
Cleaning the Cab Pre-Filter72
Cleaning the Air-Conditioning Assembly72
Storage73
Storage Safety73
Preparing the Machine for Storage73

Toro 30635 - Locating the Tie-Down Points

Table of Contents

Related product manuals