Toro 38621 Power Max 826LE User Manual

Form No. 3354-340 Rev A
Power Max™ 826LE Snowthrower
Model No. 38621 —Serial No. 260000001 and Up
Operator's Manual
Introduction
R ead this infor mation carefully to lear n ho w to operate and
maintain y our product properly and to a v oid injur y and
product damag e . Y ou are responsible for operating the
product properly and safely .
Y ou ma y contact T oro directly at www .T oro .com for
product and accessor y infor mation, help finding a dealer ,
or to register y our product.
W henev er y ou need ser vice , g en uine T oro par ts , or
additional infor mation, contact an A uthorized Ser vice
Dealer or T oro Customer Ser vice and ha v e the model and
serial n umbers of y our product ready . Figure 1 identifies the
location of the model and serial n umbers on the product.
W rite the n umbers in the space pro vided.
Figure 1
1. Model and serial number location
Model No.
Serial No.
T his man ual identifies potential hazards and has safety
messag es identified b y the safety aler t symbol ( Figure 2 ),
whic h signals a hazard that ma y cause serious injur y or
death if y ou do not follo w the recommended precautions .
Figure 2
1. Safety alert symbol
T his man ual uses 2 other w ords to highlight infor mation.
Impor tant calls attention to special mec hanical infor mation
and Note emphasizes g eneral infor mation w or th y of special
attention.
R eplacement Engine Owner’ s Man uals may be order ed
thr ough the engine man uf actur er .
© 2005—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Register at www.Toro.com. Original Instructions (EN)
Printed in the USA
All Rights Reserved

Toro 38621 Power Max 826LE Specifications

General

Brand	Toro
Model	38621 Power Max 826LE
Category	Snow thrower
Language	English

Summary

Introduction

Safety

Before Operating

Read and understand the manual and familiarize with controls before operation.

Training

Emphasizes careful reading of the manual and proper familiarization with controls.

Operation

Operation Details

Covers safe operation practices, including handling foreign objects and slopes.

Freewheeling or Using the Self-propel Drive

Explanation of how to engage or disengage the self-propel drive for different uses.

Starting the Engine

Detailed steps for starting the engine, including choke, primer, and key.

Stopping the Engine

Procedure for safely shutting down the engine.

Operating the Traction Drive

Instructions for engaging and operating the snowthrower's traction drive system.

Operating the Speed Selector

How to change speeds using the speed selector lever.

Operating the Auger/Impeller Drive

Steps to engage and disengage the auger and impeller.

Operating the Quick Stick™

How to use the Quick Stick to control chute and deflector.

Moving the Discharge Chute

Procedure for adjusting the direction of the discharge chute.

Moving the Chute Deflector

How to adjust the height of the snow discharge.

Unclogging the Discharge Chute

Steps to clear a clogged discharge chute safely.

Preventing Freeze-up

Tips to prevent controls and parts from freezing in cold conditions.

Operating Tips

General advice for safe and effective snowthrower operation.

Safety and Instructional Decals

Setup

Loose Parts

List of loose parts to verify shipment and their intended use.

Installing the Upper Handle

Instructions for attaching the upper handle to the lower handle.

Installing the Traction Control Linkage

Steps to connect the speed control rod to the traction linkage.

Installing the Chute Control Rod

Procedure for connecting the chute control rod to the control panel.

Filling the Engine with Oil

Guidance on checking and adding engine oil based on temperature.

Checking the Tire Pressure

Instructions for checking and adjusting tire pressure for shipping.

Checking the Skids and Scraper

Procedure to check and adjust skids and scraper for proper ground clearance.

Product Overview

Maintenance

Recommended Maintenance Schedule(s)

Schedule of maintenance tasks based on operating hours and time intervals.

Preparing for Maintenance

Steps to prepare the snowthrower safely before performing maintenance.

Checking the Engine Oil Level

Procedure for checking the engine oil level before each use.

Checking and Adjusting the Skids and Scraper

How to check and adjust skids and scraper for wear compensation.

Checking and Adjusting the Traction Cable

Procedure to check and adjust the traction cable for proper operation.

Checking and Adjusting the Auger/Impeller Cable

Steps to check and adjust the auger/impeller cable for proper tension.

Checking the Auger Gearbox Oil Level

Procedure for checking the auger gearbox oil level annually.

Changing the Engine Oil

Instructions for changing the engine oil after initial hours and yearly.

Lubricating the Hex Shaft

Guidance on lubricating the hex shaft yearly with engine oil.

Inspecting and Replacing the Spark Plug

Steps for inspecting, gapping, and replacing the spark plug.

Adjusting the Discharge Chute Latch

Procedure to adjust the discharge chute latch for proper locking.

Replacing the Drive Belts

Information on when and how to replace drive belts.

Storage

Preparing the Snowthrower for Storage

Detailed steps to prepare the snowthrower for long-term storage.

Removing the Snowthrower from Storage

Procedure for preparing the snowthrower after storage.

Troubleshooting

Electric starter does not turn (electric-start models only)

Troubleshooting steps for when the electric starter fails to operate.

Engine does not start or starts hard

Steps to diagnose and fix issues with engine starting.

Engine runs rough

Troubleshooting steps for an engine that runs poorly.

Engine runs, but the snowthrower discharges snow poorly or not at all

Diagnosing issues when snow discharge is ineffective.

Discharge chute either does not lock into place or does not move

Steps to fix problems with the discharge chute locking or movement.

Snowthrower does not properly clear the snow off the surface

Troubleshooting steps for poor snow clearing performance.