Toro 74922 - User Manual

72 pages

To Next Page

To Next Page

Loading...

FormNo.3394-299RevA

ZMaster

®

Professional6000

SeriesRidingMower

with48in,52in,60in,or72inTURBOFORCE

®

SideDischargeMower

ModelNo.74922—SerialNo.315000001andUp

ModelNo.74923—SerialNo.315000001andUp

ModelNo.74925—SerialNo.315000001andUp

ModelNo.74927—SerialNo.315000001andUp

ModelNo.78922—SerialNo.315000001andUp

ModelNo.78924—SerialNo.315000001andUp

g027403

Registeratwww.Toro.com.

OriginalInstructions(EN)

*3394-299*A

Table of Contents

Questions and Answers:

B
Brian RodriguezSep 1, 2025
How to fix a starter that won't crank on my Toro 74922 Lawn Mower?
- S
  Sean DaySep 1, 2025
  If the starter on your Toro Lawn Mower won't crank, check these items: * Ensure the blade-control switch is disengaged. * Engage the parking brake. * Move the motion-control levers to the NEUTRAL-LOCK position. * Make sure you are sitting in the operator’s seat. * Charge the battery if it's dead. * Check the electrical connections for good contact. * Replace the fuse if it's blown.
R
Robert FranklinAug 25, 2025
Why won't my Toro 74922 engine start?
- R
  rgordonAug 25, 2025
  If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, try the following: * Fill the fuel tank. * Open the fuel shutoff valve. * Add oil to the crankcase. * Ensure that the throttle control is midway between the 'SLOW' and 'FAST' positions. * Replace the fuel filter. * Clean or replace the air cleaner element. * Check the seat switch indicator; replace the seat if needed. * Check the electrical connections for good contact; clean the connector terminals thoroughly with electrical contact cleaner, apply dielectric grease, and reconnect. * Clean, adjust, or replace the spark plug. * Check the spark plug wire connection.
S
Shelley SchneiderSep 23, 2025
Why doesn't the clutch engage on my Toro 74922 Lawn Mower?
- A
  Andrew WareSep 23, 2025
  If the clutch on your Toro Lawn Mower doesn't engage, here are a few things to check: * The fuse may be blown. Replace the fuse. * There could be low voltage supply at the clutch. Check the coil resistance, battery charge, charging system, and wiring connections, and replace components if necessary. * The coil might be damaged. Replace the clutch. * There may be inadequate current supply. Repair or replace the clutch lead wire or electrical system. Clean the connector contacts. * The rotor/armature air gap could be too large. Remove the shim or replace the clutch.
S
Shawn TaylorSep 5, 2025
What to do if my Toro 74922 Lawn Mower machine vibrates abnormally?
- K
  Kelly WongSep 5, 2025
  If your Toro Lawn Mower is vibrating abnormally, it could be due to: * Bent or unbalanced cutting blade(s); install new cutting blade(s). * A loose blade mounting bolt; tighten the blade mounting bolt. * Loose engine mounting bolts; tighten the engine mounting bolts. * A loose engine pulley, idler pulley, or blade pulley; tighten the appropriate pulley.
K
Kimberly CummingsSep 9, 2025
What to do if my Toro Lawn Mower clutch does not engage?
- A
  Angela ToddSep 9, 2025
  If the clutch on your Toro Lawn Mower doesn't engage, it could be due to a blown fuse, low voltage supply at the clutch, a damaged coil, inadequate current supply, or a rotor/armature air gap that is too large. To address this, replace the fuse, check the coil resistance, battery charge, charging system, and wiring connections, and replace components if necessary; repair or replace the clutch lead wire or electrical system and clean the connector contacts; remove the shim or replace the clutch.
J
Jesse PetersonSep 3, 2025
How to fix an uneven cutting height on my Toro 74922?
- M
  morrisoncathySep 3, 2025
  To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or replacing bent ones. Next, level the mower deck from side-to-side and front-to-rear. Clean the underside of the mower deck. Also, ensure the tire pressure is correct. If the blade spindle is bent, contact an Authorized Service Dealer.
D
David GarciaAug 30, 2025
How to fix uneven cutting height on Toro Lawn Mower?
- J
  Jennifer Berry DDSAug 30, 2025
  To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or installing new ones if bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck, adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
A
amorganSep 12, 2025
What to do if my Toro 74922 Lawn Mower does not drive?
- L
  Lauren RamosSep 12, 2025
  If your Toro Lawn Mower doesn't drive, first check that the bypass valves are closed tight. If not, tighten them. Also, inspect the pump belt for wear, looseness, or breakage and change the belt if needed. Ensure the pump belt is correctly positioned on the pulley. Replace the spring if the idler spring is broken or missing. Finally, verify the hydraulic fluid level; add hydraulic fluid to the reservoirs if it is low, or let it cool down if it is too hot.
L
livingstonronaldSep 7, 2025
What causes abnormal vibrations in my Toro 74922 Lawn Mower?
- S
  Sherry JimenezSep 7, 2025
  If your Toro Lawn Mower vibrates abnormally, try the following: 1. Install new cutting blade(s). 2. Tighten the blade mounting bolt. 3. Tighten the engine mounting bolts. 4. Tighten the appropriate pulley.
A
April CastilloAug 27, 2025
Why Toro Lawn Mower blades do not rotate?
- A
  Angela CarterAug 27, 2025
  If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken mower deck belt; in this case, install a new deck belt. Another possibility is that the mower deck belt is off the pulley; reinstall it and check the idler pulley, idler arm, and spring for correct position and function. Also, check the pump drive belt for wear, looseness, or breakage, and adjust the belt tension or install a new belt. Finally, inspect the idler spring and replace it if it's broken or missing.

Toro 74922 Specifications

General

Fuel Type	Gasoline
Deck Material	Steel
Start Type	Recoil
Mulching Capability	Yes
Bagging Capability	Yes
Side Discharge Capability	Yes
Engine	Briggs & Stratton
Cutting Width	22 inches
Wheel Size	11 inches

Related product manuals

Preview: Toro 74920

Preview: Toro 74923

Preview: Toro Z Master 74925TE

Toro Z Master 74925TE

Preview: Toro 74920 TITAN ZX4820

Toro 74920 TITAN ZX4820

Toro 74924 TITAN ZX5420

Preview: Toro 74923 Z Master 6000

Toro 74923 Z Master 6000

Preview: Z Master Professional 6000 74922

Z Master Professional 6000 74922

Preview: Toro 74955

Preview: Toro 74950