Toro TimeCutter 6000 Series

Questions and Answers:

S
Sharon LopezAug 15, 2025
Why is my Toro TimeCutter 6000 engine overheating?
- T
  Teresa GrantAug 16, 2025
  Several factors can cause your Toro Lawn Mower engine to overheat. First, the engine load might be excessive, so reduce the ground speed. Second, check the oil level in the crankcase and add oil if it is low. Third, obstructions in the cooling fins and air passages under the engine-blower housing can cause overheating; remove any obstructions. Fourth, a dirty air cleaner can contribute to the problem, so clean or replace the air-cleaner element. If the issue persists, there may be dirt, water, or stale fuel in the fuel system, in which case you should contact an Authorized Service Dealer.
R
Ronald KlineAug 19, 2025
Why does my Toro TimeCutter 6000 Lawn Mower engine lose power?
- H
  heatheravilaAug 19, 2025
  If your Toro Lawn Mower engine loses power, consider the following potential causes: * The engine load may be too high; reduce the ground speed. * A dirty air cleaner can restrict airflow; clean the air-cleaner element. * Low oil level in the crankcase can cause power loss; add oil. * Blocked cooling fins and air passages under the engine blower housing can lead to overheating and power loss; remove any obstructions. * Faulty spark plug(s) (pitted, fouled, or with an incorrect gap) can reduce engine power; install a new, correctly gapped spark plug(s). For issues such as a blocked fuel-tank vent, dirt in the fuel filter, dirt, water, or stale fuel in the fuel system, or incorrect fuel in the fuel tank, contact an Authorized Service Dealer.
S
Seth Mejia PhDAug 23, 2025
How to fix uneven cutting height on my Toro TimeCutter 6000 Lawn Mower?
- E
  Elizabeth LambAug 23, 2025
  Uneven cutting height on your Toro Lawn Mower can result from several factors. Ensure the blade(s) is sharp; if not, sharpen them. Check for bent cutting blade(s) and replace them if necessary. Level the mower from side-to-side and front-to-rear. If applicable, adjust the anti-scalp wheel height. Clean the underside of the mower deck, and adjust the tire pressure. If a blade spindle is bent, contact an Authorized Service Dealer.
J
Judy ParkerAug 27, 2025
What to do if my Toro Lawn Mower starter does not crank?
- J
  Jocelyn CohenAug 27, 2025
  If the starter on your Toro Lawn Mower doesn't crank, check these items: * Ensure the blade-control switch is disengaged. * Make sure the motion-control levers are in the PARK position. * Check the battery and charge it if it's dead. * Inspect the electrical connections for corrosion or looseness and ensure good contact. * See if a fuse is blown and replace it if necessary. If a relay or switch is damaged, contact an Authorized Service Dealer.
T
tcruzAug 31, 2025
Why is my Toro TimeCutter 6000 Lawn Mower vibrating abnormally?
- J
  Jeffrey JonesAug 31, 2025
  Abnormal vibration in your Toro Lawn Mower can stem from several issues. Start by checking the cutting blades for bending or imbalance; if found, install new cutting blades. Then, ensure the blade mounting bolt and engine mounting bolts are tightened securely. Also, inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley. For a damaged engine pulley, bent blade spindle, or loose/worn motor mount, contact an Authorized Service Dealer.
J
Joan LopezSep 4, 2025
Why are the blades not rotating on my Toro TimeCutter 6000 Lawn Mower?
- L
  Lori AlexanderSep 4, 2025
  If the blades on your Toro Lawn Mower aren't rotating, several issues could be the cause. A worn, loose, or broken drive belt can prevent blade rotation, so install a new drive belt. Additionally, ensure the drive belt is properly installed on the pulley, checking the adjusting shafts and belt guides for correct positioning. If the power-takeoff (PTO) switch or PTO clutch is faulty, or the mower belt is worn, loose, or broken, contact an Authorized Service Dealer or install a new mower belt.
K
Kevin MillerSep 7, 2025
Why does my Toro TimeCutter 6000 Lawn Mower not drive?
- T
  Tammy OliverSep 7, 2025
  If your Toro Lawn Mower won't drive, start by checking if the bypass valves are open and close the tow valves. For issues such as worn, loose, or broken traction belts, traction belts off the pulleys, or a failed transmission, contact an Authorized Service Dealer.

Toro TimeCutter 6000 Series Specifications

General

Brand	Toro
Model	TimeCutter 6000 Series
Category	Lawn Mower
Language	English

Summary

Introduction

General Safety

Understand the manual before operating and keep bystanders away.

Safety

General Safety

Follow instructions, keep bystanders away, and operate safely.

Slope Indicator

Use the chart to determine safe operating slopes, do not exceed 15 degrees.

Safety and Instructional Decals

Locates and explains safety decals on the machine for operator awareness.

Product Overview

Identifies key components of the riding mower with numbered labels.

Controls

Familiarize yourself with all controls before starting and operating the machine.

Before Operation

Pre-operation checks and safety precautions to ensure safe use.

During Operation

Safety guidelines for operating the mower, including attentiveness and environmental conditions.

After Operation

Safety precautions to follow after the machine has been used.

Maintenance

General safety rules to follow before performing any maintenance tasks.

Before Operation

Before Operation Safety

Key safety guidelines to follow before starting the machine.

Adding Fuel

Recommended fuel type and procedure for safely filling the fuel tank.

Performing Daily Maintenance

Daily checks and procedures to perform before operating the machine.

Breaking in a New Machine

Recommendations for breaking in new engines and drive systems for optimal performance.

Using the Safety-Interlock System

Explanation of the safety system and how to test its proper function.

Positioning the Seat

Adjusting the seat forward or backward for operator comfort and control.

Adjusting the Motion-Control Levers

Adjusting lever height and tilt for maximum operator comfort.

During Operation

During Operation Safety

Safety guidelines for operating the mower, including attentiveness and environmental conditions.

Operating the Mower Blade-Control Switch (PTO)

How to engage and disengage the mower blades using the PTO switch.

Operating the Throttle

Adjusting engine speed using the throttle control from SLOW to FAST.

Operating the Choke

Using the choke control to start a cold engine.

Starting the Engine

Procedure for starting the engine, including notes on warm engines and starter safety.

Shutting Off the Engine

Steps to safely shut down the engine and park the machine.

Using the Motion-Control Levers

How to use the levers to control machine movement, including turning and maneuverability.

Driving the Machine

General advice on operating the machine, emphasizing caution and throttle use.

Driving Forward

Step-by-step guide to moving the machine forward using the motion-control levers.

Driving Backward

Step-by-step guide to moving the machine backward using the motion-control levers.

Using the Smart Speed Control System

Explanation of the 3-speed control system for different operating conditions.

Using the Side Discharge

Information on the grass deflector and safe operation with side discharge.

Adjusting the Height of Cut

How to adjust the mower deck height using the foot pedal and pin system.

Adjusting the Anti-Scalp Rollers

Adjusting anti-scalp rollers when changing the height of cut.

Operating Tips

Advice on cutting grass, using fast throttle, and maintaining the mower deck.

After Operation

After Operation Safety

Safety precautions to follow after the machine has been used.

Pushing the Machine by Hand

Instructions and warnings for manually pushing the machine.

Maintenance

Maintenance Safety

General safety rules to follow before performing any maintenance tasks.

Recommended Maintenance Schedule(s)

Schedule of maintenance tasks based on operating hours or time intervals.

Pre-Maintenance Procedures

Steps to take before starting maintenance on the machine.

Lubrication

Procedures for lubricating various parts of the machine.

Engine Maintenance

Tasks related to maintaining the engine's performance and longevity.

Fuel System Maintenance

Procedures for maintaining the mower's fuel system components.

Electrical System Maintenance

Procedures for maintaining the machine's electrical system and battery.

Drive System Maintenance

Tasks for maintaining the drive system components.

Belt Maintenance

Procedures for inspecting and replacing the mower belts.

Mower Maintenance

Tasks related to maintaining the mower deck and blades.

Pre-Maintenance Procedures

Raising the Machine

Safety precautions and methods for safely raising the machine for maintenance.

Lubrication

Greasing the Bearings

Procedure for greasing the caster wheel bearings at specified intervals.

Engine Maintenance

Engine Safety

Safety precautions specific to engine maintenance procedures.

Servicing the Air Cleaner

Steps for removing, cleaning, and installing the air cleaner elements.

Servicing the Engine Oil

Procedures for checking engine oil level and changing oil and filter.

Servicing the Spark Plug

Instructions for removing, checking, and installing spark plugs.

Cleaning the Cooling System

Procedure for cleaning the engine's cooling system and fan housing.

Fuel System Maintenance

Replacing the In-Line Fuel Filter

How to replace the in-line fuel filter following service interval guidelines.

Electrical System Maintenance

Electrical System Safety

Safety precautions for working with the machine's electrical system and battery.

Servicing the Battery

Steps for removing and servicing the machine's battery.

Servicing the Fuses

Locating and replacing fuses in the electrical system.

Drive System Maintenance

Checking the Tire Pressure

Procedure for checking and maintaining proper tire pressure for optimal performance.

Releasing the Electric Brake

Manually releasing the electric brake by rotating the link arms.

Adjusting the Tracking

How to adjust the motion-control levers to ensure the machine tracks straight.

Belt Maintenance

Inspecting the Belts

Checking belts for wear, cracks, or damage. Replace if worn.

Replacing the Mower Belt

Step-by-step guide for replacing the mower belt, including safety warnings.

Mower Maintenance

Blade Safety

Safety precautions when inspecting, sharpening, or replacing mower blades.

Servicing the Cutting Blades

Ensuring superior cut quality by keeping mower blades sharp.

Leveling the Mower Deck

Procedures to ensure the mower deck is level for an even cut.

Servicing the Cutting Blades

Checking for Bent Blades

Procedure to check mower blades for bends or imbalance.

Removing the Blades

Steps to safely remove mower blades, including handling bolts and washers.

Installing the Blades

Instructions for installing new mower blades, including torque specifications.

Leveling the Mower Deck

Checking the Side-to-Side Level

Procedure to check and adjust the mower deck for side-to-side level.

Checking the Front-to-Rear Blade Slope

Procedure to check and adjust the mower deck for front-to-rear blade slope.

Schematics

Electrical Diagram (Rev. A)

Provides a wiring diagram for the machine's electrical system.

Related product manuals

Toro TimeCutter 6000

48 pages

Toro TimeCutter MX 6050

60 pages

Toro TimeCutter HD MyRide 60in

Toro TimeCutter Z4200

52 pages

Toro TimeCutter Z5000

52 pages

Toro TimeCutter 75742

56 pages

Toro TimeCutter 75746

52 pages

Toro TimeCutter 6000 Series - User Manual

Table of Contents

Questions and Answers:

Toro TimeCutter 6000 Series Specifications

Summary

Introduction

General Safety

Safety

General Safety

Slope Indicator

Safety and Instructional Decals

Product Overview

Controls

Before Operation

During Operation

After Operation

Maintenance

Before Operation

Before Operation Safety

Adding Fuel

Performing Daily Maintenance

Breaking in a New Machine

Using the Safety-Interlock System

Positioning the Seat

Adjusting the Motion-Control Levers

During Operation

During Operation Safety

Operating the Mower Blade-Control Switch (PTO)

Operating the Throttle

Operating the Choke

Starting the Engine

Shutting Off the Engine

Using the Motion-Control Levers

Driving the Machine

Driving Forward

Driving Backward

Using the Smart Speed Control System

Using the Side Discharge

Adjusting the Height of Cut

Adjusting the Anti-Scalp Rollers

Operating Tips

After Operation

After Operation Safety

Pushing the Machine by Hand

Maintenance

Maintenance Safety

Recommended Maintenance Schedule(s)

Pre-Maintenance Procedures

Lubrication

Engine Maintenance

Fuel System Maintenance

Electrical System Maintenance

Drive System Maintenance

Belt Maintenance

Mower Maintenance

Pre-Maintenance Procedures

Raising the Machine

Lubrication

Greasing the Bearings

Engine Maintenance

Engine Safety

Servicing the Air Cleaner

Servicing the Engine Oil

Servicing the Spark Plug

Cleaning the Cooling System

Fuel System Maintenance

Replacing the In-Line Fuel Filter

Electrical System Maintenance

Electrical System Safety

Servicing the Battery

Servicing the Fuses

Drive System Maintenance

Checking the Tire Pressure

Releasing the Electric Brake

Adjusting the Tracking

Belt Maintenance

Inspecting the Belts

Replacing the Mower Belt

Mower Maintenance

Blade Safety