Toro XLS 380 - User Manual

Other manuals for Toro XLS 380

Questions and Answers:

B
barronabigailSep 12, 2025
Why Toro Lawn Mower has abnormal vibration?
- J
  James ZimmermanSep 12, 2025
  An abnormal vibration in your Toro Lawn Mower can stem from several issues. Check if the blades are bent or unbalanced, and install new blades if needed. Ensure the blade mounting bolt and the engine mounting bolts are tightened securely. Also, inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley. For a damaged engine pulley, contact an Authorized Service Dealer.
L
Linda OconnellAug 22, 2025
What to do if Toro Lawn Mower blades do not rotate?
- S
  Sydney MillerAug 22, 2025
  If the blades on your Toro Lawn Mower do not rotate, it could be due to a worn, loose, or broken blade drive belt; in this case, install a new blade drive belt. Another possibility is that the blade drive belt is off the pulley. Reinstall the blade drive belt and check the idler pulley and belt guides for the correct position.
E
elucasAug 25, 2025
Why my Toro XLS 380 Lawn Mower engine will not start?
- M
  Monica ColeAug 25, 2025
  If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, it could be due to several reasons. First, ensure the fuel tank is filled with gasoline. Check if the air cleaner is dirty and clean or replace the air cleaner element. Make sure the spark plug wire is securely connected to the spark plug, and inspect the spark plug itself—if it's pitted, fouled, or has an incorrect gap, install a new, correctly gapped spark plug. Also, verify that the choke is closing properly by adjusting the choke cable. Finally, check for dirt in the fuel filter and replace it if necessary.
M
Michael SnyderAug 26, 2025
What to do if the blades do not rotate on my Toro XLS 380 Lawn Mower?
- M
  Miranda JonesAug 26, 2025
  If the blades on your Toro Lawn Mower do not rotate, it is possible that the blade drive belt is worn, loose, or broken, in which case you should install a new blade drive belt. It could also be that the blade drive belt is off of the pulley; if this is the case, install the blade drive belt and check the idler pulley and belt guides for the correct position.
M
Maria MartinAug 28, 2025
What to do if Toro Lawn Mower engine loses power?
- D
  Daniel GarciaAug 28, 2025
  If your Toro Lawn Mower engine loses power, there are several potential causes. Start by reducing the ground speed if the engine load is excessive. Check the air cleaner and clean it if it's dirty. Ensure the oil level in the crankcase is adequate, adding oil if it's low. Also, inspect the cooling fins and air passages under the engine blower housing for obstructions. Clean or replace the fuel cap if the vent hole is plugged. Replace the fuel filter if it's dirty. Finally, make sure that your spark plug is in good condition and correctly gapped, replacing it if necessary. For issues related to stale fuel, contact an Authorized Service Dealer.
V
vsanchezAug 29, 2025
How to fix Toro XLS 380 Lawn Mower that is cutting unevenly?
- B
  Brooke JohnsonAug 30, 2025
  To fix a Toro Lawn Mower that is cutting unevenly, start by checking and setting the tire pressure to the correct levels. Ensure that the mower is level from side-to-side and front-to-rear. Also, clean the underside of the mower deck to remove any accumulated debris.
M
mcfarlandrachelSep 18, 2025
What to do if my Toro XLS 380 Lawn Mower does not drive?
- D
  Dr. Kimberly MillerSep 18, 2025
  If your Toro Lawn Mower does not drive, make sure the drive control is not in the Push position; move it to the Operate position.
M
mallorymartinSep 14, 2025
What to do if my Toro Lawn Mower starter does not crank?
- H
  herrerarobertSep 14, 2025
  If your Toro Lawn Mower starter does not crank, first ensure that the blade control (PTO) is disengaged. Next, check that the transmission drive control is in the Operate position. If these are not the issue, the battery may be dead and needs charging. Inspect the electrical connections for corrosion or looseness and ensure good contact. Finally, check if a fuse is blown and replace it if needed.
R
Rhonda MartinezSep 10, 2025
What to do if Toro Lawn Mower starter does not crank?
- A
  Andrew CampbellSep 10, 2025
  If the starter on your Toro Lawn Mower does not crank, there are several things you can check. First, ensure that the blade control (PTO) is disengaged and the transmission drive control is in the Operate position. Verify that the battery is not dead and charge it if necessary. Inspect the electrical connections for corrosion or looseness, ensuring they have good contact. Check the fuse and replace it if it's blown. For damaged relays or switches, contact an Authorized Service Dealer.
G
George TylerSep 6, 2025
Why does my Toro Lawn Mower engine overheats?
- R
  Renee HensleySep 6, 2025
  If your Toro Lawn Mower engine overheats, the engine load may be excessive, so reduce the ground speed. Check the oil level in the crankcase and add oil if it is low. Also, make sure that the cooling fins and air passages under the engine blower housing are free of obstructions; remove any debris you find.