Toshiba B-SX6T Series User Manual (English)

Other manuals for Toshiba B-SX6T Series

Owner's Manual139 pages

System Mode Manual133 pages

Maintenance Manual24 pages

Supply Loading Instructions10 pages

Questions and Answers:

J
James DuarteAug 15, 2025
Why is my Toshiba Printer not printing?
- C
  Colleen BrooksAug 15, 2025
  If your Toshiba Printer isn't printing, several factors could be at play. It might be due to a print head failure, which would require replacing the print head. Another cause could be an incomplete connection, bad contact, or broken dots in the print head connector; ensure the harness is fully connected or replace it. Problems with the ribbon take-up or supply could also be the culprit, in which case you should replace the ribbon take-up motor, ribbon feed motor, or even the MAIN PC board. Other potential causes include a MAIN PC board failure (replace the MAIN PC board), software issues (check the program), or a faulty printer cable (replace the printer cable).
A
Andrew CarterAug 18, 2025
How to fix poor print quality on my Toshiba Printer?
- C
  Christina ShawAug 18, 2025
  If your Toshiba Printer is producing poor print quality, start by checking the paper quality and use media approved by TOSHIBA TEC. A dirty print head can also cause this issue, so try cleaning it. Finally, make sure the head lever is completely fastened.
A
alexandrachoiAug 21, 2025
What to do if my Toshiba B-SX6T has a label feed failure?
- T
  Timothy FullerAug 21, 2025
  If the Toshiba Printer's label feed is failing, begin by ensuring the paper is set properly. If the issue persists, the paper quality might be the problem; use paper approved by TOSHIBA TEC. Also, try re-adjusting the feed gap sensor or black mark sensor, and set the threshold. If these steps don't resolve the problem, consider replacing the feed gap sensor or black mark sensor. Other solutions include replacing the strip feed motor or MAIN PC board if labels cannot be stripped off, properly installing the cutter mechanism, or replacing the stepping motor or MAIN PC board if the stepping motor has failed.
S
sanchezaudreyAug 25, 2025
Why is my Toshiba Printer printing blurred images?
- V
  victoria93Aug 25, 2025
  If you're experiencing blurred prints with your Toshiba Printer, it could be due to poor media quality. Try using only TOSHIBA TEC specified media. Another potential cause is dust on the media, so clean the print head and remove any dust from the media.
K
Kenneth JohnsonAug 27, 2025
What causes a ribbon end error on a Toshiba Printer?
- M
  Michael BaileyAug 27, 2025
  If your Toshiba Printer displays a ribbon end error, the issue might stem from poor ribbon quality, so ensure you are using only TOSHIBA TEC specified ribbon. Alternatively, the ribbon end sensor could be faulty, requiring replacement. In some cases, the circuit controlling the ribbon end sensor may have failed, necessitating replacement of the MAIN PC board.
M
Matthew ReynoldsAug 30, 2025
What to do if my Toshiba B-SX6T Printer power does not turn on?
- L
  Laura PattonAug 30, 2025
  If your Toshiba Printer's power does not turn on, it could be due to several reasons: * The input voltage to the printer might not be within the rated voltage, so replace the power cable or power inlet. * The output voltage from the printer might not be within the rated voltage, so replace the PS unit. * There might be no voltage to the MAIN PC board, so replace the power harness. * There may be a failure of MAIN PC Board, so replace the CPU PC board.
G
gibsontonySep 2, 2025
Why does my Toshiba B-SX6T Printer have ribbon wrinkle?
- E
  Elizabeth YangSep 2, 2025
  If your Toshiba Printer is experiencing ribbon wrinkles, it could be due to poor ribbon quality. To resolve this, use only TOSHIBA TEC specified ribbon. Another potential cause is that the ribbon is not taken up or supplied smoothly, so replace the ribbon take-up motor or ribbon feed motor.
D
Darrell MoyerSep 5, 2025
How to troubleshoot a Toshiba Printer when the LED or LCD doesn't light up?
- L
  Laura FisherSep 5, 2025
  If the LED or LCD on your Toshiba Printer does not light up, it could be due to a failure of the LED board/LCD, in which case you should replace it. Another possible cause is a failure of the LCD/LED harness, requiring replacement. The issue might also stem from a failure of the MAIN PC board, which would also need to be replaced.
A
ashleykennedySep 8, 2025
What causes dot missing on my Toshiba Printer?
- H
  harrisonmarkSep 8, 2025
  If your Toshiba Printer is missing dots in its printouts, it could be due to a broken print head element, requiring replacement of the print head. Another possibility is broken print head cable wires, in which case you should replace the print head harness. A failure of the MAIN PC board could also be the cause, necessitating its replacement.

Toshiba B-SX6T Series Specifications

General

Print Technology	Thermal Transfer / Direct Thermal
Media Thickness	0.06 mm to 0.2 mm
Connectivity	USB, Serial, Ethernet
Operating System Compatibility	Windows
Barcodes	Code 39, Code 128, Interleaved 2 of 5
2D Codes	PDF417, Data Matrix, QR Code, MaxiCode
Print Resolution	203 dpi, 300 dpi