Toshiba e-STUDIO181 User Manual (English)

Other manuals for Toshiba e-STUDIO181

Service Handbook226 pages

User Guide4 pages

Questions and Answers:

M
mistygrahamAug 21, 2025
Why is my Toshiba All in One Printer not recognized when connected to PC via USB?
- C
  Charles WilliamsAug 21, 2025
  If your Toshiba All in One Printer is not recognized when connected to your PC via USB, it could be due to the following reasons: * The USB cable may not be certified according to USB 2.0 Hi-Speed standards. Use a certified USB 2.0 Hi-Speed cable. * The printer might be connected to the PC via a USB hub. Try connecting the printer directly to the PC with a USB cable.
D
Donald FletcherAug 23, 2025
Why can't I print, scan, or set up my Toshiba e-STUDIO181 All in One Printer from a PC via USB?
- S
  Shannon LopezAug 23, 2025
  If you can't print, scan, or perform device setup on your Toshiba All in One Printer from a PC connected via USB cable, it may be because the printer is in super sleep mode. Turn the power OFF and then back ON, and try again. If the problem persists, change the settings to prevent the printer from entering super sleep mode.
D
Drew VaughanAug 25, 2025
How to fix Toshiba All in One Printer that does not turn on?
- J
  Jennifer Baker MDAug 25, 2025
  If your Toshiba All in One Printer isn't turning on, make sure the power is switched ON and that the power cable is securely plugged into the outlet.
E
Edward HillAug 27, 2025
What to do if the toner lamp is blinking on my Toshiba All in One Printer?
- H
  Heather SullivanAug 27, 2025
  If the toner lamp on your Toshiba All in One Printer is blinking, it means the toner in the cartridge has run out and you need to replace it with a new one. It may also indicate that you are using a toner cartridge not recommended by TOSHIBA. In this case, use the recommended one.
J
James LongAug 27, 2025
How to darken the copy image on my Toshiba e-STUDIO181?
- S
  Shaun RamseyAug 28, 2025
  If the copy image from your Toshiba All in One Printer is too light, it could be due to several reasons: * The toner may be running low, so replace the toner cartridge if the toner lamp is blinking. * The copy density might be set too light; adjust it to a darker setting in manual mode or switch to automatic copy density mode. * The transfer charger wire could be dirty; clean it to improve the image density.
D
Dr. Mitchell WilsonAug 29, 2025
How to fix copy paper jams in Toshiba All in One Printer?
- L
  Lisa NelsonAug 29, 2025
  If your Toshiba All in One Printer is experiencing paper jams, consider these potential causes and solutions: * Ensure you are using acceptable copy paper. * Verify that the paper size is correctly registered in the printer's settings. * Check all locations for jammed paper, using the paper jam position lamp as a guide. * Adjust the side guides in the drawer to ensure they fit the paper properly.
N
Nicole JacobsAug 30, 2025
Why is the toner lamp lit on my Toshiba All in One Printer?
- M
  Mrs. Nancy CampbellAug 30, 2025
  If the toner lamp is lit on your Toshiba All in One Printer, it could mean several things. There might be only a little toner remaining in the cartridge, but you should wait until the lamp starts blinking before replacing it. Alternatively, the toner cartridge may not be installed correctly, or you might be using a toner cartridge not recommended by TOSHIBA. Ensure the cartridge is properly installed and recommended for use.
H
Hector WilsonSep 1, 2025
How to resolve stained copy images on Toshiba All in One Printer?
- T
  Teresa McknightSep 1, 2025
  If your Toshiba All in One Printer is producing stained copy images, here are a few things to check: * Make sure that the Automatic Document Feeder or Platen Cover is fully lowered to block outside light. * Clean the original glass, platen sheet, scanning area, and guides. * Adjust the copy density to a lighter setting if it’s set too dark. * If using highly transparent originals, place a blank sheet of paper over the original.
J
Julie BerrySep 2, 2025
What to do if scanning stops prematurely on Toshiba e-STUDIO181?
- M
  mrodriguezSep 2, 2025
  If scanning stops before it is finished on your Toshiba All in One Printer, and the START lamp is lit while the FUNCTION CLEAR lamp is blinking, it could be because the number of sheets exceeds the maximum or the built-in memory is full. Press the START button to copy the data scanned so far, or press the FUNCTION CLEAR button to delete it. If only the FUNCTION CLEAR lamp is blinking, only data deletion is possible.
B
Brandon HarperSep 4, 2025
What to do if copying stops prematurely on Toshiba All in One Printer?
- S
  Stacy SpencerSep 4, 2025
  If copying stops before it is finished on your Toshiba All in One Printer, and the START lamp and the middle paper jam position lamp are lit while the FUNCTION CLEAR lamp is blinking, it likely means that approximately 250 sheets of paper have continuously exited, and the equipment stops copying to prevent the copied paper from overflowing from the tray. Remove the paper from the receiving tray, and then press the START button to resume copying. Press the FUNCTION CLEAR button to end the copy job.

Toshiba e-STUDIO181 Specifications

General

Brand	Toshiba
Model	e-STUDIO181
Category	All in One Printer
Language	English

Summary

Preface

Notice to Users

FCC NOTICE

FCC compliance details for Class A digital devices.

User Safety

Safety precautions related to laser radiation and Class 1 laser product certification.

Regulatory Information

Information on environmental preservation and battery recycling programs.

Before Reading This Manual

How to Read This Manual

Instructions on navigating the manual and understanding its layout and symbols.

Symbols in This Manual

Explains the meaning of warning, caution, and note symbols for safe operation.

TOSHIBA Quality Is Second to None

Recommended Toner Cartridges

Emphasizes using genuine TOSHIBA toner for optimal performance and features.

Supplies / Parts

Toner

Information about TOSHIBA toner quality, cost, and environmental aspects.

General

Information on service and support benefits related to TOSHIBA equipment.

General Precautions

When Installing or Moving

Safety warnings and precautions for installing and moving the equipment.

When Using the Equipment

Critical safety instructions for operating the equipment to prevent injury or damage.

During Maintenance or Inspection

Safety measures to follow during maintenance, cleaning, and inspection procedures.

When Handling Supplies

Precautions for handling toner cartridges and other supplies safely.

Disclaimer Notice

Environmental Information

ENERGY STAR® Program

Details about the ENERGY STAR program and its requirements for energy efficiency.

Energy Saving Features

Overview of features designed to reduce power consumption during idle periods.

PREPARATION

Description of Each Component

Detailed identification and explanation of the various components of the equipment.

Turning Power ON

Instructions on how to correctly turn the equipment on and its initial startup process.

Placing Copy Paper

Procedures for loading paper into the drawers and bypass tray.

Registering Size of Paper Placed

Steps to register the paper size loaded in the drawers for correct operation.

HOW TO MAKE COPIES

Placing Originals

Instructions on placing various types of originals on the glass or feeder.

Making Copies

Detailed steps for performing basic copying operations and settings.

Using Bypass Tray

Guide on using the bypass tray for special paper types and sizes.

COPYING FUNCTIONS

Default Settings

Lists the initial settings of the equipment upon installation or reset.

Paper Selection

Explains automatic and manual paper selection methods.

Zooming In/Out Copy Image

Methods for enlarging or reducing copy images and setting reproduction ratios.

Copying in Same Page Order as Originals - Sort Copying -

Instructions for performing sort copying to collate sets of copies.

Copying Both Sides of Card into 1 Page - ID CARD -

Guide to copying both sides of a card onto a single page.

Selecting Image Mode

Options for selecting optimal image quality based on original type.

Adjusting Density Level

How to manually adjust the copy density for desired output.

SETTINGS AND MANAGEMENT OF EQUIPMENT

Switching Operation Sound On/Off

Procedure to enable or disable operational sounds of the equipment.

Checking Total Number Copied

How to check the total number of pages copied or printed.

Changing of the Enabled Energy Saving Mode

Steps to modify energy saving mode settings and auto sleep timers.

TROUBLESHOOTING

When Message Lamp is Lit/Blinking

Explains the meaning of various message lamps and their troubleshooting.

Paper Jams

Detailed instructions on identifying and clearing paper jams from different locations.

Replacing Toner Cartridge

Step-by-step guide for replacing the toner cartridge.

Before Calling Service Technician

Troubleshooting common problems and when to contact service.

MAINTENANCE AND INSPECTION

Daily Inspection

Recommended daily checks and cleaning procedures for optimal performance.

Cleaning Charger

Instructions for cleaning the charger unit to prevent image staining.

Cleaning Transfer Charger

Procedure for cleaning the transfer charger wire for better image quality.

SPECIFICATIONS AND OPTIONS

e-STUDIO181 Specifications

Comprehensive list of technical specifications for the e-STUDIO181 model.

Specifications of Options

Information on the specifications of optional accessories for the equipment.

Related product manuals

Toshiba e-STUDIO181 User Manual

Table of Contents

Other manuals for Toshiba e-STUDIO181

Questions and Answers:

Toshiba e-STUDIO181 Specifications

Summary

Preface

Notice to Users

FCC NOTICE

User Safety

Regulatory Information

Before Reading This Manual

How to Read This Manual

Symbols in This Manual

TOSHIBA Quality Is Second to None

Recommended Toner Cartridges

Supplies / Parts

Toner

General

General Precautions

When Installing or Moving

When Using the Equipment

During Maintenance or Inspection

When Handling Supplies

Disclaimer Notice

Environmental Information

ENERGY STAR® Program

Energy Saving Features

PREPARATION

Description of Each Component

Turning Power ON

Placing Copy Paper

Registering Size of Paper Placed

HOW TO MAKE COPIES

Placing Originals

Making Copies

Using Bypass Tray

COPYING FUNCTIONS

Default Settings

Paper Selection

Zooming In/Out Copy Image

Copying in Same Page Order as Originals - Sort Copying -

Copying Both Sides of Card into 1 Page - ID CARD -

Selecting Image Mode

Adjusting Density Level

SETTINGS AND MANAGEMENT OF EQUIPMENT

Switching Operation Sound On/Off

Checking Total Number Copied

Changing of the Enabled Energy Saving Mode

TROUBLESHOOTING

When Message Lamp is Lit/Blinking

Paper Jams

Replacing Toner Cartridge

Before Calling Service Technician

MAINTENANCE AND INSPECTION

Daily Inspection

Cleaning Charger

Cleaning Transfer Charger

SPECIFICATIONS AND OPTIONS

e-STUDIO181 Specifications

Specifications of Options

Related product manuals