To Next PageTo Next PageWhat causes flame lifting from burner ports in my Trane Furnace?
If the flame is lifting from the burner ports on your Trane Furnace, you can try: 1. Resetting the manifold pressure (refer to the operation guide). 2. Replacing the regulator section of the combination gas valve or the entire valve. 3. Checking with your local gas supplier for the proper orifice size and replacing it (refer to the operation guide).
Why is my Trane Furnace not producing enough heat?
If your Trane Furnace is not producing enough heat: 1. Consult the operation guide. 2. Consider if the heated space has been enlarged. Have the heat loss calculated and compare it to the heater output (80% of input). Your gas supplier or installer can provide this information. If the heater is undersized, add additional heaters. 3. Replace the thermostat. 4. Check air movement through the heat exchanger. Check the voltage to the power venter motor, clean the power venter wheel and heat exchanger, and oil the power venter motor. Check filters and replace them if necessary. 5. Adjust dampers accordingly.
What to do if my Trane Furnace is producing too much heat?
If your Trane Furnace is producing too much heat: 1. Replace the thermostat. 2. Check the wiring per the diagrams, check the operation at the valve (look for shorts and correct them, such as staples piercing thermostat wiring), replace the gas valve, and refer to the operation guide.
What to do if my Trane Fan motor has a blown fuse?
If the Trane Fan motor has a blown fuse or an open circuit breaker, replace the fuse or reset the circuit breaker.
What to do if Trane Fan motor does not come up to speed?
If your Trane Fan motor isn't reaching full speed, the motor might be too small for the application, in which case you should replace it with a larger motor. Alternatively, the voltage at the motor terminals might be too low; check the voltage across the AC line and correct it if possible.
What to do if my Trane Fan motor runs and then dies down?
If your Trane Fan motor runs briefly and then stops, it could be due to a partial loss of line voltage. Check for loose connections.
How to fix a noisy flame in my Trane Furnace?
If your Trane Furnace has a noisy flame: 1. Close the air shutter and open all manual gas valves. 2. Reduce pilot gas (refer to the operation guide). 3. Replace the orifice. 4. Reset the manifold pressure (refer to the operation guide), replace the regulator section of the combination gas valve or the complete valve, or check with your local gas supplier for the proper orifice size and replace it (refer to the operation guide).
Why won't the power venter motor start on my Trane Furnace?
If your Trane Furnace's power venter motor won't start: 1. Replace the fuse or turn on the power. 2. Replace any faulty components. 3. Turn up the thermostat. 4. Replace the limit switch.
How to fix delayed ignition on my Trane Furnace?
To resolve a delayed ignition issue with your Trane Furnace: 1. Close the air shutter (refer to the operation guide). 2. Clean the main burner ports. 3. Reset the manifold pressure (refer to the operation guide). 4. Ensure the supply piping is adequately sized (refer to the installation guide). 5. Clean the pilot orifice (refer to the operation guide).
How to get rid of gas odor from my Trane Furnace?
If you smell gas coming from your Trane Furnace: 1. Inspect all gas piping and repair any leaks. 2. Clean the heat exchanger. 3. Address any drafts (refer to the installation instructions). 4. Consult the installation guide. 5. Clean the draft hood or flue collector.
General| Product Type | Air Conditioner |
|---|---|
| HSPF | Not Applicable |
| Refrigerant | R-410A |
| Voltage | 208/230V |
| Sound Level | 72 dB |
| Stages | Single Stage |
| Cooling Capacity | 1.5 - 5 Ton |
| Warranty | 10-Year Limited Warranty on Compressor |
