Trane TAM4A0C60S51ED - User Manual

18-GJ05D1-12A-EN
ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
Important: This Document is customer property and is to remain with this unit. Please return to service information
pack upon completion of work.
Important: These instructions do not cover all variations
in systems nor provide for every possible contingency to
be met in connection with the installation. Should further
information be desired or should particular problems
arise which are not covered sufficiently for the pur-
chaser’s purposes, the matter should be referred to your
installing dealer or local distributor.
Note: The manufacturer recommends installing ONLY
AHRI approved, matched indoor and outdoor systems.
Some of the benefits of installing approved matched
indoor and outdoor split systems are maximum efficien-
cy, optimum performance, and the best overall system
reliability.
Note: All AHRI ratings use a 90 second fan off delay.
Use your branded thermostat or separate relay to enable
this delay.
Note: Condensation may occur on the surface of the air
handler when installed in an unconditioned space. When
units are installed in unconditioned spaces, verify that
all electrical and refrigerant line penetrations on the air
handler are sealed completely.
Important: TAM4A0C60S51 air handler applied in
downflow or horizontal configurations should not exceed
2000 CFM. Airflow above 2000 CFM could result in
water blow-off. For verification, see airflow table.
Important: The TAM4 air handlers will only use the fol-
lowing internal electric heaters:
BAYEAAC04BK1, BAYEAAC04LG1
BAYEAAC05BK1, BAYEAAC05LG1
BAYEAAC08BK1, BAYEAAC08LG1
BAYEAAC10BK1, BAYEAAC10LG1
BAYEAAC10LG3, BAYEABC15BK1
BAYEABC15LG3, BAYEABC20BK1
BAYEACC25BK1
Convertible Air Handlers
1-1/2 – 5 Ton
Black Epoxy Coil
TAM4A0A18S11ED
TAM4A0A24S21ED
TAM4A0A30S21ED
TAM4A0A36S31ED
TAM4A0B42S31ED
TAM4A0C48S41ED
TAM4A0C60S51ED
Installer’s Guide
Standard Coil
TAM4A0A18S11SD
TAM4A0A24S21SD
TAM4A0A30S21SD
TAM4A0A36S31SD
TAM4A0B42S31SD
TAM4A0C48S41SD
TAM4A0C60S51SD
Note: Representative illustrations only included
in this document. Most illustrations display the
upflow configuration.

Summary

Safety Information

General Safety Warnings

Covers electrical, vapor, corrosion, sharp edge, and material handling hazards during installation and use.

Unit Preparation

Preparing Unit for Installation

Place Unit at Location

Setting the Unit - Vertical Installation

Vertical Installation Considerations

Downflow Installation Steps

Setting the Unit - Horizontal Installation

Horizontal Installation Considerations

Connecting the Duct work

Refrigerant Line

Refrigerant Line Connection Sizes

Lists vapor and liquid line connection sizes for various air handler models.

Refrigerant Line Brazing

Brazing Refrigerant Lines

Step-by-step instructions for brazing refrigerant lines, including safety precautions for sensors and components.

Condensate Drain Piping

Condensate Drain Piping Considerations

Connecting Condensate Drains

Electrical - Low Voltage

Low Voltage Wire Length Limits

Specifies maximum allowable lengths for low voltage wiring based on wire gauge.

Low Voltage Hook-up Instructions

Guides on drilling entry holes, routing, and securing low voltage wiring to the air handler.

Electrical - High Voltage

High Voltage Power Supply Requirements

Emphasizes matching supply voltage to the equipment nameplate and complying with codes.

Making High Voltage Connections

Start Up

System Start Up Procedure

Step-by-step guide to powering up the system and setting the thermostat for initial operation.

Checkout Procedures

Operational and Checkout Checklist

A comprehensive list of checks to verify proper installation and system performance before final operation.

Trane TAM4A0C60S51ED Specifications

General

Brand	Trane
Model	TAM4A0C60S51ED
Category	Air Handlers
Language	English