Travis Industries Tempest Torch

Other manuals for Travis Industries Tempest Torch

Troubleshooting Guide15 pages

Questions and Answers

J
Jessica NelsonAug 6, 2025
What to do if Travis Industries Outdoor Light torch lights then goes out?
- M
  Mark SinghAug 6, 2025
  If the Travis Industries Outdoor Light torch lights during the ignition sequence but then goes out during normal operation, first check that the wiring from the transformer to the torches is correct, as incorrect polarity can damage the module. Next, check the power output of the thermopile and ensure it's wired correctly, as the thermopile is polarity sensitive. Lastly, remove the glass and clean the flame spreader, burner, and Venturi (mixing tube) to remove any bugs or debris.
E
Elizabeth JamesAug 10, 2025
How to fix Travis Industries Tempest Torch Outdoor Light when torch does not light and igniter does not glow red?
- K
  Kathleen DavisAug 10, 2025
  If the Travis Industries Outdoor Light torch does not light and the igniter does not glow red, verify that there is electrical power to the module (24VAC) and check the circuit breaker or GFCI. Check the igniter by verifying OHM’s 3.5? +/- .5? and supplying 24VAC directly to it. Also, verify the polarity of the power supplied to the control module; reversed polarity may have shorted and damaged the module.
A
Allison LunaAug 14, 2025
Why are the flames too short on my Travis Industries Tempest Torch?
- G
  Gabriel RossAug 14, 2025
  If the flames of your Travis Industries Outdoor Light are too short (under 6"), it may be because the gas supply pressure to the appliance is too low. Ensure that there is enough gas in the LP tank and that the gas supply line or gas regulator is sized correctly for the load.
M
Mary WestAug 18, 2025
Why is the glass sooty on my Travis Industries Outdoor Light?
- D
  davisrandyAug 19, 2025
  If the glass of your Travis Industries Outdoor Light is sooty, check the burner and Venturi (mixing tube) for spider webs or debris. Also, windy conditions will influence the flame quality and can cause sooting.
T
Tabitha JohnsonAug 22, 2025
Why don't the flames spiral on my Travis Industries Tempest Torch Outdoor Light?
- P
  Paul OlsonAug 23, 2025
  If the flames on your Travis Industries Outdoor Light do not spiral, it could be because the torch has just been turned on and needs 5 to 10 minutes to warm up and start spiraling. Windy conditions can also affect flame quality. Verify the glass has an even gap on all four corners.
T
thenryAug 27, 2025
What to do if Travis Industries Tempest Torch Outdoor Light torch does not shut down?
- J
  John WilsonAug 27, 2025
  If the Travis Industries Outdoor Light torch does not shut down, the valve may be stuck in the open position. Check for debris in the gas supply line and replace the valve, if needed.
R
Regina GarrettOct 31, 2025
What to do if the igniter glows red but the Travis Industries Tempest Torch Outdoor Light torch does not light?
- N
  Nicole MorrisOct 31, 2025
  If the igniter glows red but the Travis Industries Outdoor Light torch doesn't light, first, make sure the gas is turned on by checking the shut-off valve. Then, verify the gas supply pressure is correct: NG should be at 7” W.C., or LP should be at 11” W.C. Check the valve by verifying OHM’s 33.2? +/- 1.0? and supplying 24VAC directly to the valve. Also, check for low power supplied to the module by verifying the voltage at the connection on the control module is a minimum of 21 volts at a 1.6 amp draw while the torch is in ignition cycle with the igniter glowing red. Ensure the wiring to the torch head is correct, the wire run from the transformer to the torch isn't too long, you're using the proper wire gauge for the length of the wire run, and you haven't exceeded the number of torches ...

Summary

General Information

Product Overview

Details gas-fired torch types: Natural Gas and Propane.

Safety Warnings

Highlights critical warnings for outdoor use and potential fire/explosion hazards.

Testing and Certification

Information on testing and listing by OMNI-Test Laboratories, Inc.

Introduction

Manual Overview

Manual details installation, operation, and routine maintenance for the Tempest torch.

Listing Details

Specifies standards and certifications the torch was tested against.

Registration and Service

Information on serial numbers, warranty registration, and service contacts.

Safety Precautions

Installation and Usage Requirements

Emphasizes adherence to local codes, outdoor use, and handling of gas.

Operational Hazards

Covers risks like using incorrect fuel, flame issues, and operating in storms.

Maintenance and Service Safety

Stresses qualified installation, annual inspection, and parts modification.

Features and Specifications

Product Features

Lists key features like BTU input, materials, igniter, and glass type.

Installation Options

Details available mounting methods: Wall, Post, and Pier.

Technical Specifications

Provides input ratings, orifice sizes, burner ports, and pressure for NG/LP.

Installation

Installation Warnings

Critical warnings regarding qualified installers, outdoor use, and insurance notification.

Packing List

Lists all components included in the torch package.

Required Items and Order

Lists required base assemblies and the recommended installation sequence.

Placement Requirements

Location Restrictions

Advises against placing the torch in high-traffic or debris-prone areas.

Clearance Specifications

Details minimum clearance distances from ground and combustibles.

Gas Line Requirements

Code Compliance and Testing

Mandates installation per codes and safe pressure/leak testing procedures.

Fuel Configuration and Connection

Explains NG/LP differences, non-convertibility, and gas line connection.

Post Mount and Control Cover Installation

Control Cover Attachment

Details detaching and reattaching the control cover to the post mount.

Gas Line and Torch Assembly to Post

Steps for connecting gas line and attaching torch assembly to post mount.

Torch Assembly

Burner Top and Support Bars

Instructions for seating the burner top and attaching support bars.

Glass Installation

Guidance on installing glass panels, including caution for overtightening.

Optional Rain Cap Installation

Rain Cap Mounting Procedure

Describes how to place and secure the rain cap using studs and nuts.

Wall Mount Kit

Wall Mount Application

Explains the use of the optional kit for wall mounting the torch.

Post or Pier Mounted Torch

Mounting Configurations

Illustrates deck mounting and free-standing post mount configurations.

Operation

Before Operation

Advises reading the manual, removing covers, and inspecting the torch.

Dry Weather Lighting

Step-by-step guide for using the built-in igniter to light the torch.

Operation Procedures

Wet Weather Lighting

Instructions for lighting the torch using a wand lighter in wet conditions.

Turning the Torch Off

Explains how to safely shut off the torch using the valve control.

Maintenance

Routine Maintenance

Guidance on regular cleaning, inspection, and glass care.

Winterizing Procedure

Procedures for protecting the torch during winter or long periods of non-use.

Replacement Parts

Parts Identification

Diagram and list identifying all replaceable parts of the torch.

Troubleshooting

Common Problems and Solutions

Lists common issues like no light or short flames and their causes/solutions.

Warranty Information

Year 1 Coverage Details

Details covered parts and labor for the first year of ownership.

Warranty Conditions and Exclusions

Outlines requirements, limitations, and conditions that void the warranty.

Warranty Service Procedure

Steps to follow when warranty service is required, including dealer contact.