TREND IQ4E User Manual

IQ4E/.. Installation Instructions - Mounting TG201338 Issue 4, 19-Jan-2016. Applies to v3.33. 1
Installation Instructions - Mounting
IQ4E/..
Controller
Important: Retain these instructions
These instructions shall be used by trained service
personnel only.
If the equipment is used in a manner not
specied by these instructions, the protection provided by the
equipment may be impaired.
https://partners.trendcontrols.com
GB DE DK FIES FR
IT NL NO RU
PL SE
1
Dimensions
WARNING Removal of cover exposes dangerous
voltages.
WARNING To reduce the risk of electrical shock or re
do not interconnect the output of different Class 2 circuits
.
It is recommended that the installation should comply
with the local electrical safety installation practices (e.g.
HSE Memorandum of Guidance on Electricity at Work
Regulations 1989, USA National Electric Code).
Any connected devices must be insulated from mains by
reinforced insulation.
3 INSTALLATION
1 BOX CONTENTS 2 STORING
CONTENTS
1 Box Contents .................................................................1
2 Storing ...........................................................................1
3 Installation .....................................................................1
Note: For temperatures below 0°C (32°F) special care must be
taken that there is no condensation on or within the unit.
IQ4E/.. Installation
Instructions - Mounting
(TG201338)
IQ4/IC/TERM
I/O Bus Terminator
4 Removing From DIN Rail ............................................11
5 Field Maintenance .......................................................12
6 Disposal .......................................................................12
7 End User Licence Agreement .....................................12
Labels used on IQ4E
!
Caution, consult
documentation
Caution, possibility
of electric shock
230 Vac input
power connector
RS232 Local
Supervisor Port
Wallbus
connector
Auxiliary supply
output connector
nn
n
Universal input
connector
USB (for future use) Terminator switch
(/XNC only)
Bias switch
(/XNC only)
RS-485
(/XNC only)
Ethernet indicators
and connector
84
85
86 87
Trend current
loop connector
Auxiliary supply
output connector
n
nn
Analogue output
connector
USB Local
Engineering Port
Service button/
indicator
Power indicator Watchdog indicator
LAN OK indicator I/O Bus indicator
192.5 mm (7.55”) 58.5 mm (2.3”)
53.5 mm (2.11”)
110 mm (4.33”)
116 mm (4.57”)
HO
2
+60°C
(+140°F)
0
-25°C
(-13°F)
90%RH

TREND IQ4E Specifications

General

Brand	TREND
Model	IQ4E
Category	Controller
Language	English

Summary

Box Contents

Storing

Installation

IQ4E Labels and Indicators

Describes various labels and their meanings for IQ4E installation.

IQ4E Mounting Requirements

Details environmental and installation site requirements for the IQ4E controller.

Mounting the IQ4E on DIN Rail

Explains the procedure for mounting the IQ4E unit onto a DIN rail.

Connecting Power Supply to IQ4E

Provides instructions and safety notes for connecting the power supply to the IQ4E.

Connecting Ethernet Interface

Explains how to connect the Ethernet interface for network communication.

Connecting Universal Inputs

Explains how to connect various universal input types to the controller.

Connecting Analogue Outputs

Details the connection of analogue output terminals for control signals.

Connecting Auxiliary Supply Output

Explains how to connect auxiliary power outputs for external devices.

Connecting Trend Current Loop Network

Details connecting to the current loop network for LAN variants.

Connecting to XNC Interface

Explains connecting to XNC interfaces via RS-485, RS-232, or Ethernet.

Connecting Wallbus

Details how to connect the Wallbus for communication with other devices.

Installing and Connecting I/O Modules

Explains how to install and connect additional I/O modules to the I/O bus.

Closing Covers and Panel

Instructions for closing the unit's rotating covers and the main panel/enclosure.

Configuring IQ4E Controller

Refers to separate guides for configuring the controller and I/O modules.

Removing from DIN Rail

Removing IQ4E from DIN Rail

Details the procedure for detaching the IQ4E unit from the DIN rail.

Field Maintenance

Product Disposal

End User License Agreement