1
Quick Instruction Overview
0n Play recorded message n where n = 1 to 8. (Page-30)
0#n Record message n where n = 1 to 8. Max = 14 seconds per message. (Page-30)
0*n Delete message n where n = 1 to 8. (Page-30)
1nnnn Set site ID code. (Default = 1234) (Page-14)
1#n-n Add a Keypad Entry Code to pool memory. (Page-21)
1*n-n Delete a Keypad Entry Code from pool memory. (Page-21)
2n Set a Phone Number in List-A. (Page-23)
2#n Set the Volume Level Control. (Default = 0 = Automatic) (Page-13)
2*n Set the Ring Rollover Limit on placed calls. (Default = 6) (Page-12)
3nnnn Set the Programming Access Code. (Default = 2468) (Page-14)
3#n-n Add a Card Code to pool memory. (Batch loading is allowed) (Page-22)
3*n-n Delete a Card Code from pool memory. (Page-22)
4n Set Automatic Message Options. (Default = 2) (Page-16)
4#n Set TED, Dial Looping and Button Modes. (Default = 2) (Page-14)
4*n Set Code Range Functions. (Default as all disabled) (Page-29)
5n Set Rings Counted before unit Auto Answers. (Default = 3) (Page-11)
5#nn Set Modem Extension Code. (Default = 99) (Page-13)
5*nn Set Touch Tone Extension Code. (Default = 00) (Page-13)
6n Set Dialout Modes. (Default = 0) (Page-12)
6#n Set Keypad Options. (Default = 0) (Page-15)
6*n Set Security Mode. (Default = 0) (Page-12)
7n Set Gate1 Cycle Interval in 5 second periods. (Default = 3) (Page-10)
7#n Set Gate2 Cycle Interval in 5 second periods. (Default = 3) (Page-10)
7*n Set Gate3 Cycle Interval in 5 second periods. (Default = 3) (Page-10)
7n Set Phone Number in List-B. (in TA3 mode only) (Page-23)
8nnn Set Call Length Limit in seconds. (Default = 180) (Page-13)
8#n Set Alarm Interval in 5 second periods. (Default = 3) (Page-10)
8*n Set MG3/HF3/TA3 & Passback options. (Default = 0) (Page-15)
9nn Assign a Tone to a Function for when unit dials out normally. (Page-24)
9#nn Assign a Tone to a Function for when unit has been called remotely. (Page-24)
9* Activate Tone Echo Test if unit called. (use # tone to exit this test) (Page-34)
9* Force unit into a Standard Touch Tone Phone test mode. (Page-34)
*n View a Phone Number in List-A. (Page-23)
**n View a Phone Number in List-B. (Page-24)
*#0 View Setup Assignments. (Page-16)
*#1 View Database Structure and Capacities. (Page-16)
*#2n# View Residence Data. (n = Resident Code to start at or omit n = 1st) (Page-17)
*#3 View the System Clock. (Page-20)
*#4n# View Pooled Entry Codes. (n = Entry Code to start at or omit n = 1st) (Page-21)
*#5n# View Pooled Card Codes. (n = Card Code to start at or omit n = 1st) (Page-22)
*#6 View all active Code Ranges. (Page-29)
*#7n# View Time Zone Tables. (n = Zone Code to start at or omit n = 1st) (Page-28)
*#8 View Macro Code Tables. (Page-32)
*#9 View Function Tone Assignments. (Page-24)
*#* View Greeting Screens 1 and 2. (Page-26)
*## View Custom Prompt Lines 1 to 8. (Page-26)
*** View Embedded Programming Guide. (this page embedded) (Page-34)
#0 Set Residence Phone Numbers. (Page-17)
#0# Auto Display Prompting for faster Keypad Data Entry of Res# and Phone# (Page-17)
#1 Set Residence Entry Codes and Card Codes. (Page-18,19)
#2 Delete Residence Entry Code and Card Codes. (Page-18,19)
#3 Set System Clock. (Page-20)
#4 Set Time Zones. (Page-27)
#5 Set Macro Commands. (Page-33)
#6 Edit Custom Greeting Screen 1. (if enabled and local only) (Page-26,9)
#7 Edit Custom Greeting Screen 2. (if enabled and local only) (Page-26,9)
#8 Edit Prompting Messages. (if enabled and local only) (Page-26,9)
#9 Edit Residence Names. (if enabled and local only) (Page-3,9)
#*n Master Erase Commands. (use extreme caution here) (Page-34)
## Exit Programming Mode.
To Next Page
Loading...