To Next PageTo Next PageWhat to do if red “LOAD” light is flashing on Tripp Lite Battery Charger?
If the red “LOAD” operation indicator light is flashing on your Tripp Lite Battery Charger, the inverter is likely overloaded. Reduce the load. To reset the unit, move the Operating Mode Switch to “DC OFF,” wait 1 minute, and then switch to “AUTO/REMOTE” or “CHARGE ONLY.”
Why is the red “LOW” battery light flashing on my Tripp Lite Battery Charger?
If the red “LOW” battery indicator light is flashing on your Tripp Lite Battery Charger with the Operating Mode Switch in the “AUTO/REMOTE” position, it could be due to low battery voltage, causing the unit to shut down to protect the battery. If AC power is present, the unit will automatically reset and start recharging. If you're using an external charger, manually reset the unit by moving the Operating Mode Switch to “DC OFF” for two seconds, then back to “AUTO/REMOTE.” Another cause might be a false reading from undersized or poorly connected DC cabling. Ensure you're using DC cable of sufficient size that is sufficiently connected to the Inverter/Charger.
Why is my Tripp Lite Battery Charger not recharging?
If your Tripp Lite Battery Charger isn't recharging with AC input present, the connected batteries might be dead, so check and replace them if necessary. Also, the battery fuse might be blown, so inspect and replace it if needed. Lastly, make sure the battery cabling is securely connected; check and tighten or replace the cabling if it's loose.
What does it mean when all three “BATT VOLT/ CHRG CURR” LEDs are rapidly flashing on Tripp Lite Battery Charger?
If all three “BATT VOLT/ CHRG CURR” LEDs are rapidly flashing on your Tripp Lite Battery Charger while in “AUTO/ REMOTE” mode, the battery is likely overcharged, causing the unit to shut down to prevent damage. This may be due to connected auxiliary chargers or the unit’s charger. Disconnect any auxiliary chargers. Reset the unit by moving the Operating Mode Switch to “DC OFF,” wait 1 minute, and then switch back to “AUTO/REMOTE.”
What does it mean when all three “BATT VOLT/ CHRG CURR” LEDs are slowly flashing on Tripp Lite Battery Charger?
If all three “BATT VOLT/ CHRG CURR” LEDs are slowly flashing on your Tripp Lite Battery Charger with the Operating Mode Switch in the “AUTO/ REMOTE” position, the battery is excessively discharged. The unit will shut down to prevent battery damage. Use an auxiliary charger to raise the battery voltage. Check external battery connections and the fuse. The unit will automatically reset when the condition is cleared.
General| Output power | 2000 W |
|---|---|
| Output current | 25 A |
| Output voltage | 120 V |
| Country of origin | China |
| Product color | Black |
| Dimensions (WxDxH) | 215.9 x 412.8 x 184.2 mm |
| Package dimensions (W x D x H) | 15 x 21.5 x 13.25 \ |
| Package depth | 535.9 mm |
| Package width | 365.8 mm |
| Package height | 325.1 mm |
| Package weight | 19500 g |
| Harmonized System (HS) code | 8504.40.9570 |
| Quantity per master (outer) case | 1 pc(s) |
Weight and Dimensions| Depth | 412.8 mm |
|---|---|
| Width | 215.9 mm |
| Height | 184.2 mm |
| Weight | 18140 g |
Contains critical warnings for safe installation, operation, and storage of the Inverter/Charger, covering location, battery, equipment, and operation.
Explains how to select and use the AUTO/REMOTE, CHARGE ONLY, and DC OFF operating modes.
Recommends Deep Cycle batteries and matching the type to DIP switch settings for optimal performance.
Detailed steps for securely mounting the Inverter/Charger, including clearance and fastener types.
Guidelines for DC wiring, recommended cable gauge, length, and terminal torque for efficient connection.
Lists common symptoms, problems, and their corrections for Inverter/Charger issues.
