Why TSC MH340 power indicator does not illuminate?
If the power indicator on your TSC Barcode Reader does not illuminate, it could be due to a couple of reasons. Check if the power cord is properly connected to both the printer and the outlet, and plug it in securely. Also, make sure the power switch is turned on.
Why is RTC time incorrect when rebooting my TSC MH340?
If the RTC time is incorrect when you reboot your TSC Barcode Reader, the battery may have run down. Check if there is a battery on the main board.
How to correct the left side printout position on TSC MH340?
If the left side printout position is incorrect on your TSC Barcode Reader, it could be due to a wrong label size setup. Set the correct label size. Also, the parameter Shift X in the LCD menu might be incorrect; fine-tune it by pressing [Menu] [Setting] [Shift X].
What to do if my TSC Barcode Reader can’t download the file to memory?
If your TSC Barcode Reader can’t download the file to memory (FLASH / DRAM/CARD), it means that the memory is full. Delete unused files in the memory.
What to do if TSC MH340 carriage is open?
If your TSC Barcode Reader carriage is open, please close the print carriage.
What does 'Take Label' mean on my TSC MH340?
The 'Take Label' message on your TSC Barcode Reader indicates that the peel function is enabled. If the peeler module is installed, remove the label.
What to do if my TSC MH340 is not feeding labels stably?
If the label feeding is not stable (skew) when printing with your TSC Barcode Reader, it's likely because the media guide isn't touching the edge of the media. If the label is moving to the right side, move the label guide to the left.
What to do if TSC Barcode Reader is printing labels with missing left or right side?
If your TSC Barcode Reader is missing printing on the left or right side of the label, it is likely due to an incorrect label size setup. Set the correct label size.
What to do if TSC MH340 prints gray line on blank label?
A gray line on a blank label from your TSC Barcode Reader typically indicates that the print head or platen roller is dirty. Clean both the print head and the platen roller.
How to fix poor print quality on my TSC MH340?
Poor print quality on your TSC Barcode Reader can be due to several reasons. First, reload the ribbon and media, ensuring they are correctly installed. Clean the print head if there's dust or adhesive accumulation. Adjust the print density and print speed. If the ribbon and media are incompatible, change to proper ribbon or label media. Adjust the printhead pressure adjustment knob.
General| Print technology | Direct thermal / Thermal transfer |
|---|---|
| Maximum resolution | 300 x 300 DPI |
| Maximum printing width | 104 mm |
| Display type | LCD |
| Product color | Black |
| Built-in display | Yes |
| Display resolution | 320 x 240 pixels |
| Maximum media length | 11430 mm |
| Maximum roll diameter | 203.2 mm |
| Supported paper width | 20 - 114 mm |
| AC input voltage | 100 - 240 V |
| Power source type | AC |
| AC input frequency | 50 - 60 Hz |
| Sustainability certificates | ENERGY STAR |
| Storage temperature (T-T) | -40 - 60 °C |
| Operating temperature (T-T) | 5 - 40 °C |
| Storage relative humidity (H-H) | 10 - 90 % |
| Operating relative humidity (H-H) | 25 - 85 % |
| Wi-Fi | - |
| Serial interface type | RS-232 |
| Connectivity technology | Wired & Wireless |
| Ethernet LAN data rates | 10, 100 Mbit/s |
| Flash memory | 512 MB |
| Storage media | Flash |
| Internal memory | 256 MB |
| Built-in barcodes | 1D, 2D, AZTECCODE, Code 11, Code 128 (A/B/C), Code 39, Code 49, Code 93, Code-128 Codabar Library, Data Matrix, EAN128, EAN13, EAN8, GS1 DataBar, Interleaved 2/5, MaxiCode, MicroPDF417, PDF417, QR Code, UPC-A, UPC-E |
| Compatible memory cards | MicroSD (TransFlash) |
| Page description languages | TSPL-EZ |
Weight and Dimensions| Depth | 502 mm |
|---|---|
| Width | 276 mm |
| Height | 326 mm |
Explanation of LEDs, keypads, touch screen, and power-on utilities.
Physical setup of the printer and connecting it to a computer.
Instructions for loading ribbon, media, fanfold, peel-off, and rewinder media.
Adjusting printhead pressure to ensure optimal print quality.
Key safety guidelines, CE statements, and RF exposure information.
To Next Page