To Next Page
J
James SandersSep 23, 2025
Why is the cutter not working on my TSC MH361T?
- GGregory WhiteSep 23, 2025
If the cutter is not working on your TSC Barcode Reader, the connector may be loose. Plug in the connect cable correctly.
Why is the cutter not working on my TSC MH361T?
If the cutter is not working on your TSC Barcode Reader, the connector may be loose. Plug in the connect cable correctly.
Why is my TSC MH361T printing with poor quality?
Poor print quality on your TSC Barcode Reader can occur due to several reasons. The ribbon and media might be loaded incorrectly, there could be dust or adhesive on the print head, the print density or speed might not be set properly, the printhead element could be damaged, the ribbon and media might be incompatible, or the printhead pressure might not be set properly. Reload the supply, clean the print head and platen roller, adjust the print density and print speed. Run a printer self-test to check the print head test pattern for missing dots. Change to proper ribbon or label media. Adjust the printhead pressure adjustment knob and ensure the print carriage is closed properly.
What to do if my TSC MH361T has a paper jam?
If your TSC Barcode Reader has a paper jam, it could be due to the gap/black mark sensor not being set properly, incorrect label size settings, or labels stuck inside the printer mechanism. Calibrate the media sensor, set the correct media size, and remove any stuck labels from inside the printer.
How to fix no print on the label with my TSC MH361T Barcode Reader?
If your TSC Barcode Reader is not printing on the label, it may be because the label or ribbon is loaded incorrectly, you're using the wrong type of paper or ribbon, or the print density setting is incorrect. Follow the media and ribbon loading instructions. Verify that the ribbon and media are compatible and that the ribbon-inked side is correct. Reload the ribbon, clean the printhead, and set the correct density with the media.
What to do if my TSC MH361T Barcode Reader skips labels when printing?
If your TSC Barcode Reader skips labels during printing, the label size might not be specified properly, the sensor sensitivity might not be set correctly, or the media sensor could be covered with dust. Check if the label size is set up correctly. Calibrate the sensor using Auto Gap or Manual Gap options. Clear the GAP/Black mark sensor with a blower.
Why is the left side printout position incorrect on my TSC MH361T?
If the left side printout position is incorrect on your TSC Barcode Reader, the label size setup might be wrong or the parameter Shift X in the LCD menu is incorrect. Set the correct label size and press [Menu] ? [Setting] ? [Shift X] to fine-tune the parameter of Shift X.
What to do if my TSC MH361T Barcode Reader SD card is unable to use?
If your TSC Barcode Reader's SD card is not working, the SD card may be damaged or not inserted correctly. Use a supported capacity SD card and insert the SD card again.
What to do if my TSC MH361T takes label?
If your TSC Barcode Reader displays 'Take Label', the peel function is enabled. If the peeler module is installed, remove the label. If there is no peeler module, switch off the printer and install it. Check if the connector is plugged in correctly.
What to do if my TSC Barcode Reader is missing printing on the left or right side of label?
If your TSC Barcode Reader is missing printing on the left or right side of the label, the label size setup might be wrong. Set the correct label size.
Why is my TSC Barcode Reader LCD panel dark and keys not working?
If the LCD panel on your TSC Barcode Reader is dark and the keys are not working, the cable between the main PCB and LCD panel might be loose. Check if the cable between the main PCB and LCD is secured.
Describes the touch LCD panel, buttons, and status indicators for operating the printer.
Step-by-step guide to connect and set up the printer for first-time use.
Instructions for properly installing a ribbon into the printer.
Procedure for safely removing a used ribbon from the printer.
Step-by-step guide for loading label media into the printer.
Details how to adjust the print head pressure for optimal print quality.
Provides steps to adjust printer mechanisms to prevent ribbon wrinkles.
Explains how to calibrate and configure media sensors for accurate printing.
Tools and procedures for diagnosing printer issues, including print config and self-tests.
Guide to identify and resolve common issues encountered while operating the printer.
Methods and tools for cleaning the printer's internal and external components.
General| Brand | TSC |
|---|---|
| Model | MH361T Series |
| Category | Barcode Reader |
| Language | English |
