What to do when TSC Barcode Reader shows memory full error?
If your TSC Barcode Reader displays a memory full error (FLASH / DRAM), it indicates that the space in the FLASH/DRAM is full. To resolve this, delete any unused files stored in the FLASH/DRAM.
Why are the Power and Error LEDs blinking fast on my TSC Barcode Reader?
If the Power and Error LEDs are blinking rapidly on your TSC Barcode Reader, it is likely due to turning the power switch OFF and ON too quickly. Turn off the printer, wait until all LEDs are dark, and then turn the printer back on.
Why is the RTC time incorrect when I reboot my TSC Barcode Reader?
If the RTC time is incorrect when you reboot your TSC Barcode Reader, the battery on the main board may have run down. Check if there is a battery on the main board.
Why is the cutter not working on my TSC Barcode Reader?
If the cutter is not working on your TSC Barcode Reader, it may be due to a loose connector. Ensure that you plug the connect cable in correctly.
Why is my TSC Barcode Reader's LCD panel dark, but LEDs are lit and the label is feeding forward?
If your TSC Barcode Reader's LCD panel is dark while the LEDs are lit and the label is feeding forward, it indicates that the LCD panel harness connector is loose or plugged upside down.
What causes irregular printing on my TSC Barcode Reader?
Irregular printing on your TSC Barcode Reader can occur if the printer is in Hex Dump mode; turn the printer off and on to exit this mode. Additionally, incorrect RS-232 settings can cause this issue, so reset the RS-232 settings.
How to resolve wrinkle problem on TSC Barcode Reader printouts?
To address wrinkle issues on printouts from your TSC Barcode Reader, ensure that the printhead pressure is correctly adjusted. Also, verify that the ribbon is installed correctly and set the suitable density to achieve good print quality. Finally, make sure the label guide touches the edge of the media guide.
Why is my TSC Barcode Reader unable to use the SD card?
Your TSC Barcode Reader may be unable to use the SD card for a few reasons. The SD card itself might be damaged, so try using a supported capacity SD card. Ensure the SD card is inserted correctly. The SD card manufacturer may not be approved; refer to section 2.2.3 for a list of supported SD card specs and approved manufacturers.
Why is printing missing on the sides of labels from TSC Barcode Reader?
If printing is missing on either the left or right side of labels from your TSC Barcode Reader, it is likely due to an incorrect label size setup. Ensure that you set the correct label size to resolve this issue.
How to improve poor print quality on my TSC Barcode Reader?
To enhance the print quality of your TSC Barcode Reader, begin by reloading the supply to ensure the ribbon and media are correctly loaded. Clean the printhead to remove any accumulated dust or adhesive. Adjust the print density and print speed settings. If the issue persists, run a printer self-test to check the print head test pattern for any missing dots, which could indicate a damaged printhead element. Ensure that the ribbon and media are compatible. Lastly, adjust the printhead pressure adjustment knob to optimize the pressure.
General| Resolution | 203 dpi / 300 dpi |
|---|---|
| Operating Temperature | 5°C to 40°C (41°F to 104°F) |
| Print Method | Thermal Transfer & Direct Thermal |
| Interface | USB |
| Power Supply | AC 100-240V, 50/60Hz |
| Humidity | 20% to 85% RH (non-condensing) |
Overview of TSC ME240/ME340 thermal label printers.
Details standard and optional features of the ME240/ME340 printers.
Physical, electrical, and environmental specifications of the printer.
Resolution, printing method, speed, and size for print jobs.
Details on ribbon size, length, core, width, and winding type.
Specifications for label roll capacity, types, width, thickness, and core diameter.
Instructions for unpacking and inspecting the printer and its accessories.
Visual identification of printer components and their locations.
Identifies front panel keys, indicators, and covers.
Identifies internal components like spindles, sensors, and print head.
Identifies rear interfaces, power switch, and SD card slot.
Explains the function of front panel keys and LED indicators.
Details the function of standard and optional front panel keys.
Explains the meaning of status indicated by POWER, ON-LINE, and ERROR LEDs.
Step-by-step guide for connecting and setting up the printer.
Procedures for installing and loading the ribbon.
Procedure for installing a ribbon roll into the printer.
Instructions for loading various types of media into the printer.
Instructions for loading a standard roll label.
Instructions for loading fan-fold media.
Procedure for loading media when using the peel-off module.
Procedure for loading media when using the cutter module.
Guide for adjusting print head pressure for optimal print quality.
Visual representation of the printer's menu structure.
Visual representation of the printer's menu structure for setup options.
Configuration options for TSPL2 printer language, covering various settings.
Configuration options for ZPL2 printer language, covering various settings.
Options for checking sensor status and performing calibration (Gap, Bline, Cont.).
Settings for adjusting vertical (Label Top) and horizontal (Left Position) print placement.
Configuration for serial port parameters like baud rate, parity, data bits, and stop bits.
Settings for network connectivity, including IP address, MAC, DHCP, and static IP.
Functions for managing files stored on the printer's memory (DRAM, Flash, Card).
Tools for printing configuration, dump mode data, and rotating the cutter.
Options to change the display language of the printer's LCD.
Options to initialize printer settings and view mileage information.
Guide to launching and using the TSC Diagnostic Utility software.
Explains printer functions available in the utility and lists factory default settings.
Steps to configure Ethernet settings using a USB connection.
Steps to configure Ethernet settings using an RS-232 serial connection.
Steps to configure Ethernet settings directly over the network.
Lists common printer issues and their solutions.
Instructions and methods for cleaning printer parts like print head and platen roller.
To Next Page
