TurboChef 3240 - Page 87

APPENDIX A - REPLACING OVEN COMPONENTS
A-13
Item Part Number Hardware Description Hardware Part
Number(s)
Blower Motor, Upper HHC-6520 Key, 3/16
Shim, Shaft Seal
Sealing Block, Blower
Washer, Wave Spring
Clamp, Blower Seal
Nut, 1/4-20, Serrated Hex Flange, Plated Steel
100731 (to wheel)
700-0284 (to wheel)
NGC-1024 (to wheel)
102436 (to wheel)
NGC-1023 (to wheel)
100906 (x8 - to oven)
Blower Motor Controller (BMSC), Upper 103580 Nut, #6-32, Serrated Hex Flange, SS 100902 (x4)
Blower Wheel, Upper 103567 See “Blower Motor” hardware See “Blower Motor”
Bracket, CMSC HHC-6606 Screw, #8 x 3/8, Sht Mtl, PPHD, Type A, SS
Nut, #10-32, Serrated Hex Flange, SS
101696 (x4)
100903 (x4)
Bracket, Dual Fan Mounting HHC-6371 Screw, 1/4-20 x .38 Lg, PFH, SS, 100
O
101389 (x3 - to oven)
Combustion Motor Controller (90
o
, Nat Gas) HHC-6630-3 Screw, #8 x 3/8, Sht Mtl, PPHD, Type A, SS
Nut, #10-32, Serrated Hex Flange, SS
101696 (x4)
100903 (x4)
Combustion Motor Controller (Inline, Nat
Gas)
HHC-6630-4 Screw, #8 x 3/8, Sht Mtl, PPHD, Type A, SS
Nut, #10-32, Serrated Hex Flange, SS
101696 (x4)
100903 (x4)
Combustion Motor Controller (90
o
, Propane) HHC-6630-5 Screw, #8 x 3/8, Sht Mtl, PPHD, Type A, SS
Nut, #10-32, Serrated Hex Flange, SS
101696 (x4)
100903 (x4)
Combustion Motor Controller (Inline,
Propane)
HHC-6630-6 Screw, #8 x 3/8, Sht Mtl, PPHD, Type A, SS
Nut, #10-32, Serrated Hex Flange, SS
101696 (x4)
100903 (x4)
Cover, Blower Insulation, Upper HHC-6367 See “Blower Motor” hardware See “Blower Motor”
Fan, Cooling, Lower 100083 Standoff, 10-32 x 1.50 Lg, 3/8 Hex, Stl/Zn Plt
Washer, #10 Flat, SS
Washer, #10 Split Lock
Screw, 10-32 x 2.5 Lg, Hex Head, SS
101927 (x3 - to fan)
102140 (x3 - to bracket)
102350 (x3 - to bracket)
101384 (x3 - to bracket)
Fan, Cooling, Upper 100083 Standoff, 10-32 x 1.50 Lg, 3/8 Hex, Stl/Zn Plt
Washer, #10 Flat, SS
Washer, #10 Split Lock
Screw, 10-32 x 2.5 Lg, Hex Head, SS
101927 (x3 - to fan)
102140 (x3 - to standoff)
102350 (x3 - to standoff)
101384 (x3 - to standoff)
Heat Slinger, Blower, Upper 102708 See “Blower Motor” hardware See “Blower Motor”
Plate, Blower Motor, Upper HHC-6405 Screw, 1/4-20 x .50, Hex Serrated Washer Head, SS
Spacer, Blower Motor
101394 (x4)
NGC-1022 (x4)
Plate, Blower Mounting, Upper HHC-6404 Screw, 1/4-20 x .50, Hex Serrated Washer Head, SS
Spacer, Blower Insulation Cover
101394 (x4)
HHC-6366 (x4)
Switch, Momentary, Mushroom (Idle Button) 102831 None N/A
Thermostat, 120F, Close on Rise 102086 Screw, 6-32 x 3/8, Sht Mtl Drill Point, PPHD, Zinc 101684 (x2)
Wire Harness, Cooling Fan HHC-6598-2 None N/A