Tylo Sense Pure User Manual (English)

Other manuals for Tylo Sense Pure

Installation And User Guide31 pages

Installation Guide52 pages

Questions and Answers:

D
Donald RobinsonAug 1, 2025
Why does the Tylo Sense Pure Heater element in the stone compartment not warm up?
- D
  Donna VelazquezAug 2, 2025
  If the heater element in your Tylo Heater's stone compartment isn't warming up, consider these possibilities: * Verify that the temperature settings on the control panel are correctly set for heater element operation. * Check the fuses on the main switchboard, as tripped fuses can prevent heating. Replace or reset them as needed. * It's possible that the resistor coil in the heater element is faulty or there's an internal heater PCB fault, which requires an authorized electrician to diagnose.
A
Alexandra SmallAug 6, 2025
How to fix lights that don't come on in my Tylo Sense Pure sauna?
- H
  Holly ValentineAug 6, 2025
  If the lights in your sauna don't come on when switched on at the control panel of your Tylo Heater, consider the following: * The internal glass fuse in the heater might be faulty. To resolve this, switch off the main power switch on the heater and replace the glass fuse. * Verify if the lighting is connected via the heater by consulting with the authorized electrician who installed the heater/lighting. * An internal heater PCB fault could also be the cause, requiring an authorized electrician to find the fault.
E
Emma JonesAug 11, 2025
What to do if my Tylo Sense Pure Heater is not working?
- A
  Aaron MolinaAug 11, 2025
  If your Tylo Heater isn't working, first ensure that the main power switch is turned on. If the switch is already on, check the fuses in the distribution board and replace or reset any that have blown or tripped.
L
laura05Aug 17, 2025
What to do if my Tylo Heater does not work and the control panel doesn't light up?
- S
  Samantha WillisAug 17, 2025
  If your Tylo Heater isn't working and the control panel remains dark, there are several potential causes: * Ensure the main power switch is turned on. * Check the fuses on the main switchboard and replace or reset them if necessary. * Inspect the cabling between the heater and control panel for loose connections. If found, switch off the heater's main power, reconnect the cables securely, and then switch the power back on. If the problem persists, consult an authorized electrician. * The internal temperature cut-out may have been triggered. Try resetting the heater temperature cut-out.
D
debbieriveraAug 22, 2025
What to do if the Tylo Sense Pure Heater fuses trip immediately when turned on?
- K
  kellimckinneyAug 22, 2025
  If the fuses or ground fault interrupt device on the main switchboard trip as soon as you turn on the Tylo Heater, it indicates a potential short-circuit. Here's what to do: * Do not use the heater. * Switch off the heater at the main switchboard. * Disconnect the heater fuses on the main switchboard. Possible causes include a short-circuit at the heater GND (potentially due to a faulty heater element), faulty lighting connected to the heater, an insulation fault in the heater element due to prolonged inactivity, or excessive water exposure. An authorized electrician is required to find the fault.
H
Howard StewartAug 27, 2025
Why is my Tylo Sense Pure Heater not working if the temperature cut-out is activated?
- S
  Susan WebbAug 27, 2025
  If the internal temperature cut-out has been activated, your Tylo Heater will not work. You should check and fix the cause of this activation. If you're unsure about the cause, it's best to contact a professional for assistance.

Tylo Sense Pure Specifications

General

Frequency	50 Hz
Material	Stainless steel
Stone Capacity	20 kg
Installation	Wall-mounted
Color Options	Stainless steel
Type	Sauna Heater
Voltage	400 V
Control System	Digital control panel
Room Size	5-12 m³
Safety Features	Overheat protection
Heating Technology	Electric heating elements
Thermostat	Integrated thermostat