Unicorn DB2-H515 -  󵠯󴑇  ; Table of Contents

 ꌯ 󶃏󴳧   

1. 주요부품명칭 / NAMES OF MAJOR PAR TS
2. 사양 / SPEC IFICATIONS
․․․․․․․․․․․․․․․․․․
1
3. 테이블 치수 / THE TABLE SIZE
․․․․․․․․․․․
2
4. 설치 / INSTALLATION
․․․․․․․․․․․․․․․․․․․․․
2
1. 유수판설치/Installing the oil pan ․․․․․․․․․․․․․ 3
2. 무릎올림장치설치/Installing the knee lifter assembly
․․․ ․․․․․․ ․․․․
․․
․․ ․․․․ ․․․․․․․
․․
․ ․․․․ ․․․․․․․․
․․․ 3
3. 벨트설치/Installing the belt
․․․․ ․․․․․․․․ ․
․․
․․․ ․․․․․․
5
4. 밑실감는법/Installing the bobbin winder
․․․ ․․․․․․ ․․․․
5
5. 벨트커버조립법/Installing the belt cover
․ ․․․․ ․․․․․․․
5
6. 사립봉부착법/Installing the cotton stand
․․․․ ․․․․․․․․
6
7. 급유/Lubrication
․․․․ ․․․․․․․․
․․
․․․․ ․․․․․․․․ ․
․․
․․․ ․․․
6
5. 봉재전 준비
/ PREPARATION BEFORE SEWING
․․․․․
7
1. 바늘의 설치/Installing the needle
․․․․․․․․ ․․․․
․․․
․․․
7
2. 북집의 분리/Removing the bobbin case
․․․․
․
․․ ․․․
7
3. 밑실감는법/Winding the lower thread ․
․ ․
․
․․․․․ ․․․․․
8
4. 밑실설치법/Installing the bobbin case ․
․ ․․․․ ․․․․․․․
9
5. 윗실조절법/Threading the upper thread
․․․ ․․․
․․․ 9
6. 땀수조절법/Adjusting the stitch length
․․․․ ․․․․ ․․
10
7. 실채기사용법/Using the thread wiper
․․․․ ․․․․
․․․․ 10
6. 재 봉 / SEWING
․․․․․․․․․․․․․․․․․․․․
11
1. 재봉/Sewing
․ ․․․․ ․․․․․․ ․․․․․․․ ․․․․ ․․․․ ․․․․․․․․ ․․
11
2. 역전/Backtacking
․ ․․․․ ․․․․․․ ․․․․․․․ ․․․․ ․․․․ ․․․․․
11
7. 실 장 력 / THREAD TEN SION
․․․․․․․․․․․․
12
1. 실장력조절/Adjusting the thread tension
․․․․ ․․․
12
2. 사절후윗실잔사량조절법/Adjusting the trailing
length after thread trimming
․․․ ․․․․․․ ․․․․ ․․․
13
3. 노루발압력조절법
/Adjusting the presser foot pressure
․․․․․․․․ ․․․․
13
8. 청 소 / CLEANING
․․․․․․․․․․․․․․․․․․․․
14
9. 이동칼과 고정칼의 위치 조정 / REPLAC ING
THE FIXED KNIFE AND MOVABLE KNIFE
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
15
10. 표준 조정 / STAND ARD ADJUSTMENTS
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
16
1. 실장력스프링조정법
/Adjusting the thread tension spring
․․ ․
․
․
16
2. 실가이드조정법
/Adjusting arm thread guide R
․․․ ․․․․ ․
17
3. 노루발높이조정법
/Adjusting the presser foot height
․․․․ ․․
18
4. 톱니높이조정법/Adjusting the feed dog height
․ ․․․․
19
5. 톱니각도조정법/Adjusting the feed dog angle
․․․․ ․․
19
6. 침봉높이조정법
/Adjusting the needle bar height
․ ․․․ ․․․ ․
20
7. 바늘및가마타이밍조정법/Adjusting the needle and
rotary hook timing
․ ․․․․ ․․․ ․․․ ․․․․․․․ ․․․ ․
․․ 20
8. 이송타이밍조정법/Adjusting the needle and
feed mechanism timing
․․ ․․․․ ․․․․․․․․ ․․․․ ․․
21
9. 위치검출기조정법/Adjusting the synchronizer
․ ․․
22
10. 상축과 가마의 급유량 조정법
/Adjusting the upper shaft and
rotary hook lubrication amount
․ ․․ ․․․ ․․․․․․․
23
조정표 / TROUBLESHOOTING GUIDE
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
24
All manuals and user guides at all-guides.com