Unify OpenScape CP400 Quick Reference Guide

Using your OpenScape Desk Phone CP400
Place a call
• Lift handset, dial number or
• Dial number and lift handset or
• For handsfree mode or if headset is connected:
dial number.
Answer a call
• Lift handset or
• for handsfree mode: press : or
• if headset is connected: press ..
End a call
•Hang up, or
• For handsfree mode: press : or
• If headset is connected: press..
Dial from Conversation List
1. Press Soft Key "Conversations" from Menu screen.
2. Press € and μ to select the desired conversation or
type in start of name.
3.
Press Z and lift handset.
Open listening
During a call with handset:
• Press :.
Switch off open listening:
• Press :.
Switch between Handset and Handsfree Mode
Switch to handsfree mode during a Call:
• Hold down : until you hang up handset.
Switch to handset:
• Lift handset.
Using your OpenScape Desk Phone CP400
Consultation
During a call with Party A:
1. PressZ. Party A is put on hold.
2. Call Party B.
3. If the conversation with Party B is finished, press
Z or
wait, until Party B has hang up.
You are now connected again to Party A.
Toggle
During a call with Party A:
1. PressZ. Party A is put on hold.
2. Call Party B.
3. If connected to Party B, press „Toggle“ _, to toggle.
Pressing „Toggle“ _ repeatedly toggles between Party A
and B.
Make a conference call
During a call with party A:
1. PressZ. Party A is automatically put on hold.
2. Call party B.
3. Once connected with party B, press „Conference“ _.
You are now connected in a conference with parties A
and B.
Transfer a call
During a call with party A:
1. PressZ. Party A is automatically put on hold.
2. Call party B.
3. Once connected with party B, press „Transfer“ _. Al-
ternatively, the call can be transferred already before
announcing the call.
The party A will be transfered to party B.
Call back
1. Call an internal Party. The Party does not lift the hand-
set or is busy.
2. PressZ, the call back is activated.
3. As soon as the not reached Party has hung up, the call-
back is triggered and your telephone rings..
4. Answer the call back. The not reached Party is called.
Using your OpenScape Desk Phone CP400
Program Call Forwarding for all Calls
1. Press\.
2. Select "Forward all calls" with « .
3. Press Soft Key
K .
4. Enter the destination number and press
Z .
5. Press
\ .
Turn Call Forwarding on/off for all Calls
•Press\.
• Press Soft Key "Without condition" to toggle between
on/off.
Program Favourites
1. Press @.
2. Press Soft Key "Favourites".
3. Press Soft Key K to enter edit mode.
4.
Press Soft Key K to enter desired Soft Key.
5.
Press Soft Key K to enter normal key function.
6. Press € and μ to select the desired function.
7.
Press Soft Key Q to confirm.
8. If required, edit the label and/or settings.
9.
Press Soft Key Q to save your changes.
10.
Press Soft Key Q to leave Favourites edit mode.

Unify OpenScape CP400 Specifications

General

Handset type	Wired handset
Product type	IP Phone
Product color	Black
Display diagonal	3.7 \
Backlight display	Yes
Display resolution	240 x 120 pixels
Volume control	Buttons
Number of programmable keys	16
Caller ID	-
Lines quantity	- lines
Phonebook capacity	1000 entries
Security algorithms	128-bit AES, 256-bit AES, HTTPS
Networking standards	IEEE 802.3az
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	IP v4/v6 (SIP) IPv4 (HFA), DHCP,
Number of handles included	- pc(s)
Operating system installed	Linux
Ringer type	MP3
Voice codecs	G.711, G.722, G.729, G.729A, G.729B
Safety	CISPR22 Class B, CISPR 24 EN55032 Class B, EN55024 FCC Part 15 (CFR 47) Class B
Certification	CE NRTL FCC Part 68 (CFR 47) / CS-03 Part V
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	5 - 70 °C
Headset connectivity	DHSG/EHS
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	165 mm
Width	283 mm
Height	143 mm
Weight	1200 g