Union Switch & Signal GENISYS II - User Manual

1000 TECHNOLOGY DRIVE
PITTSBURGH, PA 15219-3120
SM-6900B
Hardware Installation
GENISYS

II
Non-Vital Logic Emulator
And Remote Control Interface
COPYRIGHT 1999 Union Switch & Signal Inc. All Rights Reserved.
PRINTED IN USA
August 1999
UNION SWITCH & SIGNAL
THIS DOCUMENT AND ITS CONTENTS ARE THE PROPERTY OF UNION SWITCH & SIGNAL INC.
(HEREINAFTER US&S
®
) FURNISHED TO YOU ON THE FOLLOWING CONDITIONS: NO RIGHT OR
LICENSE IN RESPECT TO THIS DOCUMENT OR ITS CONTENTS IS GIVEN OR WAIVED IN SUPPLYING
THE DOCUMENT TO YOU. THIS DOCUMENT OR ITS CONTENTS ARE NOT TO BE USED OR
TREATED IN ANY MANNER INCONSISTENT WITH THE RIGHTS OF US&S AND ARE NOT TO BE
COPIED, REPRODUCED, DISCLOSED TO OTHERS OR DISPOSED OF EXCEPT WITH THE PRIOR
WRITTEN CONSENT OF US&S.
'-----'~

Union Switch & Signal GENISYS II Specifications

General

Manufacturer	Union Switch & Signal
Category	Control Unit
Model	GENISYS II
Input Voltage	24 VDC
Operating Temperature	-40°C to +70°C

Summary

1. General Information

1.4 Installing a GENISYS II System

Outlines the fundamental steps involved in the installation of the GENISYS II system.

2. Cardfile and Circuit Board Installation

2.1 Installing the Cardfile

2.1.1 Mounting and Environment

2.1.3 Power Input

Describes the DC power requirements and surge protection for the GENISYS II cardfile.

2.1.3.1 Source

Specifies the voltage range, nominal values, and ripple requirements for the DC power source.

2.1.3.2 Wiring and Surge Protection

Details wiring guidelines and essential surge protection devices for safe power input.

2.2 Installing the GENISYS II Cardfile Plug-ins

Guides the user through the process of installing plug-in circuit boards into the cardfile.

2.2.1 Circuit Board Installation Rules

2.2.2 Keying Plug Installation

2.2.3 Printed Circuit Board Jumper and Firmware Configurations

Details the jumper and firmware settings required for configuring CPU and power supply boards.

2.2.3.1 Configuring the CPU Board

Provides specific instructions for configuring the CPU board's jumpers and settings.

2.2.3.2 Configuring the GENISYS II Power Supply

Describes the necessary configurations for the GENISYS II system power supply board.

2.3 PCB Connector Assembly and Cardfile Address Setting

Covers the assembly of PCB connectors and the setting of cardfile addresses.

2.3.1 General

2.4 Circuit Board Connections to External Circuits

Explains how to connect various circuit boards to external devices and systems.

2.4.1 CPU Board

Details the serial port connections and interface wiring for the GENISYS II CPU board.

2.4.2 Non-Vital I;O PCBs

2.4.3 Non-vital 32-Bit Output PCBs

2.4.4 Local Control Panel Driver; External Input PCBs

2.4.5 Cable Jumper Settings

3. Installing GENISYS II System Peripheral Devices

3.2 Connecting GENISYS II to External Serial Devices

Guides the connection of the GENISYS II system to various external serial devices.

3.2.1 General Description of GENISYS II Serial Ports

3.2.3 Connecting to RS-485 Serial Ports

3.2.4 Connecting to RS-423 Serial Ports

3.2.5 Connecting to RS-232 Serial Ports

3.2.6 Isolation of Serial Port Signal Common

Stresses the importance of serial port signal common isolation to prevent ground loops and damage.

3.2.7 Physical Connections to Serial Ports

3.2.8 Configuring GENISYS II Serial Ports in the Application Program

Details how to configure GENISYS II serial ports within the application program for various scenarios.

3.2.9 Configuring GENISYS II CPU Serial Communication Jumpers

Explains the configuration of specific CPU serial communication jumpers for proper operation.

3.3 Serial Communication Adapter Panel